P R O G L I D E
S T E A M
I R O N
complies with
INTERNATIONAL
Model:
23600A
IEC60335
2400W
SAFETY SPECIFICATIONS
max
PLEASE READ ALL INSTRUCTIONS BEFORE USE
2 y e a r g u a r a n t e e
23600A_IM.indd
1
2012/05/22 11:28:59 AM
n
n-
o
IMPORTANT SAFEGUARDS:
•
When using the steam function for the first
time, do not direct the steam towards the
laundry, as there could be debris from the
steam vents.
When using your iron, basic safety precautions
should always be followed:
•
Make sure the voltage used corresponds with
that indicated on the rating label.
Use the iron only as described in this instruc-
tion manual.
Filling with water:
•
•
Make sure that both the variable steam con-
e-
g
trol and temperature control dial are in the
“OFF” position.
Close supervision is necessary when any appli-
ance is used near children. Do not leave iron unat-
tended while plugged in or on an ironing board.
Burns can occur from touching hot metal parts, hot
water or steam.
•
•
Hold the iron upright so that the water-filling
inlet is in a horizontal position.
n
d
Pour water through the water filling inlet until
the water reaches the “MAX” mark indicated
on the side of the iron, and never fill above
this mark.
•
This appliance is not intended for use by per-
sons (including children) with reduced physi-
cal, sensory or mental capabilities, or lack
of experience and knowledge, unless they
have been given supervision or instruction
concerning use of the appliance by a person
responsible for their safety. Children should
be supervised to ensure that they do not play
with the appliance.”
e
r,
Setting the temperature:
Follow the ironing instructions on the garment la-
bel. If there are no instructions but you do know
the kind of fabric, please consult the table below.
Note: If the fabric consists of various kinds of fab-
rics, always select the temperature required by the
n
t,
s
•
•
The iron should never be left unattended most delicate fabric.
while it is connected to the wall socket.
er
Unplug the iron from the wall socket before:
FABRIC
Synthetic
Silk, wool
TEMP. CONTROL
TEMP. REQUIREMENT
Low temperature
1) Cleaning
•
e
2
r,
n
2) Filling with water or emptying the water
tank
••
Medium temperature
Cotton, linen
•••
High temperature
3) Immediately after use
•
Never operate the iron with a damaged power
cord or plug, or if it is damaged in any way. To
avoid the risk of electric shock, do not disas-
semble the iron. Take it to your nearest ap-
proved service centre for repair.
Steam ironing:
•
Place the iron in a vertical position and set the
temperature control dial to the “MIN“ heat set-
ting.
•
•
Do not let the power cord touch hot surfaces.
To protect against electric shock, do not im-
merse the iron in water or any other liquid.
The iron must be used and rested on a stable
surface.
•
Insert the plug into the wall socket, and then
turn the temperature control dial to the “MAX”
heat setting. The pilot light will illuminate, indi-
cating that the iron is heating up.
When the pilot light switches off, the selected
temperature has been reached and the iron is
ready to use.
-
d
d
•
•
•
•
•
Do not use the iron if there are visible signs of
damage or if it is leaking.
,
-
During ironing, the pilot light will switch on/off
automatically as the thermostat maintains the
selected temperature.
e
BEFORE FIRST USE:
•
It is normal for a small amount of smoke to be
released on first use, this will quickly disap-
pear.
Turn the variable steam control to the desired
position.
23600A_IM.indd
3
2012/05/22 11:29:00 AM
•
Steam is produced as soon as the iron is held
horizontally.
socket, lift the iron with the filling hole down-
wards to empty the remaining water from the
water tank.
Spraying:
Press the spray button to spray water on the
clothes, as often as required.
•
Insert the plug into the wall socket, and set
the temperature control dial to “MAX” for 1-2
minutes to evaporate the remaining water,
and then unplug the iron and let it cool down
before storing it.
•
Note: When using the water spray function, ensure
that there is enough water in the water tank. You
may have to pump the spray button several times
when using for the first time.
ATTENTION:
The iron must not be left unattended while it is
connected to the wall socket. If the power cord is
Burst of steam:
•
Push the burst of steam button to generate damaged, contact your nearest authorized service
a powerful burst of steam that can penetrate
fabrics and smooth the most difficult creases.
center for repair.
Wait for a few seconds before pressing again. In case of any repairs or replacement of the power
By pressing the burst of steam button at in- cord or plug, contact your nearest authorized ser-
•
tervals you can also iron vertically (curtains,
hanging garments, etc.)
vice center for repair.
Note: The burst of steam function can only be used Note:
at the“MAX“ temperature setting. Only use this
function when the pilot light turns off.
•
This appliance is not intended for use by per-
sons (including children) with reduced physi-
cal, sensory or mental capabilities, or lack
of experience and knowledge, unless they
have been given supervision or instruction
concerning use of the appliance by a person
responsible for their safety.
Dry ironing:
When ironing without steam, follow the “steam
ironing” section. Ensure that the variable steam
control remains in position “O” (no steam).
•
•
•
Children should be supervised to ensure that
they do not play with the appliance.
The iron must not be left unattended while it is
connected to the wall socket.
Self-cleaning:
The self-cleaning feature cleans inside the sole-
plate, removing impurities. We recommend using
this function every 10-15 days.
The plug must be removed from the wall
socket before the water tank is filled with wa-
ter.
•
Set the variable steam control to position “O”
(no steam).
•
The filling aperture must not be opened dur-
ing use. Instructions for the safe refilling of the
water tank is given.
•
•
Fill the water tank to maximum level.
Set the temperature control dial to “MAX” and
wait for the pilot light to switch off.
•
•
Remove the plug from the wall socket and
press the self-cleaning button until the boiling
water, steam and impurities escape.
When the soleplate has cooled down, you
can clean it with a damp cloth
How to clean and store:
After using, remove the plug from the wall
•
23600A_IM.indd
4
2012/05/22 11:29:00 AM
TROUBLE SHOOTING
Problem
Reason
Action
Pre-caution
Iron is leaking water.
Temperature is too low
Set the temperature to steam setting (cotton)
Check fabric type is suitable for high steam
temperature
Steam switch is on self clean
function
Turn steam switch setting to steam or 0
position
Switch steam setting to 0 (off) after use or
when filling tank.
Tank is overfilled
Empty water tank
Fill to MAX mark only.
Iron is in the horizontal position
too long.
When adjusting item place iron down in the
vertical position
If iron is left on the item in the horizontal
position for too long it may burn the fabric.
Check temperature setting is suitable for
fabric type.
Iron is not heating up
Temperature control dial is in
the off position
Turn the temperature control dial to the
desired temperature setting.
Switch on household socket
Check the socket with another appliance
Household socket is off.
Household socket is not
working
Ensure iron is in the upright position.
Appliance must be of similar wattage to
prevent overloading.
Iron is tripping mains
Overloaded circuit.
Unplug all appliances attached to the same
circuit and check iron.
Note that there can be up to 5 household
plug sockets on 1 circuit.
Iron sticking to clothing
Temperature is too hot
Turn down temparature on control dial.
Clean and rinse item.
Check temperature setting is suitable for
fabric type.
Clothing is dirty or not rinsed
thoroughly.
Use spray function to dampen item and
check temperture is correct.
Use an old linen cloth to remove any trace
of dirt on the soleplate. Use iron soleplate
cleaner or methylated spirits for bad marks.
Check temperature setting is suitable for
fabric type.
Creases not coming out
Not Enough Steam
Item is too dry or temperature
too low.
Use steam function.
The steam control is off or set
too low.
Set the steam button/switch to on or full.
Ensure temperature control dial is set to the
3 dot position for steaming.
The iron temperature is
too low.
Set temperature control dial to MAX or 3 dot
position for steaming.
Check temperature setting is suitable for
fabric type.
The steam valve is blocked
due to water scale.
If your iron is fitted with a self clean function
carry out cleaning as per instructions.
Use distilled or demineralised water in your
iron to prevent blocking.
23600A_IM.indd
5
2012/05/22 11:29:00 AM
23600A_IM.indd
6
2012/05/22 11:29:00 AM
|
Lantronix Pole Saw 900 560 User Manual
Leica Saw Lecia SP1600 User Manual
Lenovo Laptop 114155U User Manual
Lowrance electronic GPS Receiver LCX 17M User Manual
Magnavox Flat Panel Television 19MD301B User Manual
Makita Drill 8390DWAE User Manual
Makita Drill DA391D User Manual
Makita Trimmer EM2650LH User Manual
Maytag Range 8111P375 60 User Manual
Maytag Washer 2206679 User Manual