Planet Technology Switch GT 80X User Manual

10/100/1000Base-T to 1000Base-SX/LX  
Gigabit Ethernet Media Converter  
User’s Manual  
 
If you find information in this manual that is incorrect,  
misleading, or incomplete, we would appreciate your  
comments and suggestions.  
FCC Warning  
This equipment has been tested and found to comply with  
the regulations for a Class A digital device, pursuant to Part  
15 of the FCC Rules. These limits are designed to provide  
reasonable protection against harmful interference when the  
equipment is operated in a commercial environment. This  
equipment generates, uses, and can radiate radio frequency  
energy and, if not installed and used in accordance with  
this user’s guide, may cause harmful interference to radio  
communications. Operation of this equipment in a residential  
area is likely to cause harmful interference, in which case  
the user will be required to correct the interference at his  
own expense.  
CE Mark Warning  
This is a Class A product. In a domestic environment, this  
product may cause radio interference, in which case the  
user may be required to take adequate measures.  
 
WEEE Warning  
To avoid the potential effects on the  
environment and human health as a result  
of the presence of hazardous substances  
in electrical and electronic equipment, end  
users of electrical and electronic equipment  
should understand the meaning of the  
crossed-out wheeled bin symbol. Do not dispose of WEEE  
as unsorted municipal waste and have to collect such WEEE  
separately.  
Revision  
User’s manual for PLANET Gigabit Ethernet Converter  
For Models: GT-802, GT-802S, GT-805A, GT-806A15, GT-  
806B15, GT-806A60, GT-806B60  
Rev 1.0 (August. 2007)  
Part No: 2010-AA4230-000  
 
Table of Contents  
Chapter 1 OVERVIEW......................................................6  
About the Gigabit Ethernet Media Converter................6  
Chapter 2 PRODUCT FEATURES........................................7  
Chapter 3 MODEL LIST ...................................................9  
Chapter 4 CHECKLIST...................................................10  
Chapter 5 PRODUCT OUTLOOK ......................................11  
Chapter 6 INSTALLING THE CONVERTER.........................13  
6.1 Stand-alone Installation .....................................13  
6.2 Chassis Installation and Rack Mounting ...............16  
Chapter 7 DUPLEX MODE SUPPORT................................18  
Chapter 8 LED INDICATION...........................................19  
Chapter 9 CABLE CONNECTION PARAMETER...................20  
Chapter 10 PRODUCT SPECIFICATION............................22  
Chapter 11 POWER INFORMATION .................................24  
 
Chapter 1 OVERVIEW  
Thank you for purchasing PLANET GT-80X family Gigabit  
Ethernet Media Converter products. This Gigabit Ethernet  
Media Converter is used to convert one type media signal to  
other type equivalent that allows two type segments connect  
easily, efficiently and inexpensively. The Gigabit Ethernet  
Media Converter introduced here provides one channel  
media conversion between the 10/100/1000Base-T and  
1000Base-SX/LX,1000Base-SX/LX through SFP Mini-GBIC  
(GT-805A only) or the 1000Base-LX WDM (GT-806A15/B15  
and GT-806A60/B60 only).  
This Gigabit Ethernet Media Converter can be used as a  
standalone unit or as a slide-in module to the 10”/19”  
media chassis (up to 15 units) for a multi-mode and single-  
mode Fiber combined networks at a central wiring closet.  
Please contact with your sales representative for more about  
the 10”/19” media chassis.  
About the Gigabit Ethernet Media Converter  
This Gigabit Ethernet Media Converter utilizes a netrwork  
technology specified by IEEE 802.3 10Base-T, IEEE 802.3u  
100Base-TX, IEEE 802.3ab 1000Base-T and IEEE 802.3z  
1000Base-SX/LX standards. The Gigabit Ethernet Media  
Converter is used to converter one type media signal  
to other type equivalent that allows two type segments  
connect easily, effciently and inexpensively.  
 
Chapter 2 PRODUCT FEATURES  
● Comply with IEEE 802.3 10Base-T, IEEE 802.3u 100Base-  
TX, IEEE 802.3ab 1000Base-T, IEEE 802.3z 1000Base-SX/  
LX Ethernet standard  
● Bridge mode media converter with TP port supports  
10/100/1000Base-T auto-negotiation and auto-MDIX  
● Auto-Negotiation for 10/100/1000Base-T; Half-Duplex or  
Full-duplex for 100Mbps and 10Mbps  
● LED indicators for simple diagnostics and management  
● Fiber Interface  
● Compact in size, easy installation  
● Can be installed on PLANET’s 10”/19” Media Converter  
Chassis (MC-700/1000R/1500)  
GT-802  
1000Base-SX interface for up to 550 meters (multi-mode  
50/125µm fiber) and 220 meters (multi-mode 62.5 /125µm  
fiber)  
GT-802S  
1000Base-LX interface for up to 10km (single mode  
9/125µm fiber) and up to 550m (multi-mode fiber cable)  
GT-805A  
One SFP (Mini-GBIC) slot supporting either multi-mode or  
single mode fiber, exibility in Gigabit Ethernet fiber-optic  
wiring with different Mini-GBIC module installed  
 
GT-806A15 / GT-806B15  
1000Base-LX WDM interface for up to 15km (single mode  
9/125µm fiber)  
GT-806A60 / GT-806B60  
1000Base-LX WDM interface for up to 60km (single mode  
9/125µm fiber)  
 
Chapter 3 MODEL LIST  
Your Gigabit Ethernet Converter comes with one of the  
following models.  
• GT-802: 10/100/1000Base-T to 1000Base-SX(SC)  
• GT-802S: 10/100/1000Base-T to 1000Base-LX(SC)  
• GT-805A: 10/100/1000Base-T to 1000Base-SX/LX(LC)  
• GT-806A15: 10/100/1000Base-T to 1000Base-LX(WDM)  
• GT-806B15: 10/100/1000Base-T to 1000Base-LX(WDM)  
• GT-806A60: 10/100/1000Base-T to 1000Base-LX(WDM)  
• GT-806B60: 10/100/1000Base-T to 1000Base-LX(WDM)  
In the following sections, the term “GT-80X” indicates the  
product family above, the term “MM” and “SM” represent  
Multi-Mode and Single Mode fiber-optic mode.  
Please note GT-806A15/806B15 and GT-  
806A60/806B60 is designed to work  
together. It means you must connect GT-  
806A15 to GT-806B15 or GT-806A60 to  
Notice:  
GT-806B60 from them to work normally.  
If both ends are GT-806A15 or GT-806A60  
and GT806B15 or GT-806B60, they can’t  
work normally and may damage the fiber  
connectors.  
 
Chapter 4 CHECKLIST  
Your GT-80X carton should contain the following items:  
• The Gigabit Ethernet Converter  
• AC-DC Power Adapter (Output: 5VDC, 2A max.)  
• This user’s manual  
If any item is missing or damaged, please consult the dealer  
from whom you purchased your Gigabit Ethernet Converter.  
GT-805A is with one vacant SFP module  
slot. The mini GBIC SFP module is not  
bundled with in the package.  
Notice:  
10  
 
Chapter 5 PRODUCT OUTLOOK  
Right View (GT-80X)  
GT-802/GT-802S  
GT-805A  
GT-806A15/B15/A60/B60  
Left: Fiber-optic connector, Right: TP connector.  
Two LED indicators per TP, ber port.  
11  
 
Rear View (GT-80X)  
One DC jack for DC power input.  
12  
 
Chapter 6 INSTALLING THE CONVERTER  
6.1 Stand-alone Installation  
To install a GT-80X stand-alone, on a desktop or shelf,  
simply complete the following steps:  
Step 1: Turn off the power of the device/station in a  
network to which the GT-80X will be attached.  
Step 2: Ensure that there is no activity in the network.  
Step 3: Attach fiber cable from the GT-80X to the fiber  
network. TX, RX must be paired at both ends.  
Step 4: Connect the 5VDC power adapter to the GT-80X  
and verify that the Power LED lights up.  
Step 5: Turn on the power of the device/station; the PWR  
LEDs should light when all cables are attached.  
13  
 
Figure 6-1 GT-80X installation  
Please refer to Section 9 for detailed wiring  
information of the GT-80X.  
Notice:  
To prevent from optic acceptor malfunction,  
check the both wires / transmitter before  
power on the converter.  
14  
 
GT-805A Installation  
Step 1: Connect the fiber cable. Attach the duplex LC  
connector on the network cable into the SFP  
transceiver.  
Step 2: Attach fiber cable from the GT-805A to the fiber  
network. TX, RX must be paired at both ends.  
Step 3: Connect the 5VDC power adapter to the GT-805A  
and verify that the Power LED lights up.  
Step 7: Turn on the power of the device/station; the PWR  
LEDs should light when all cables are attached.  
Figure 6-2 GT-805A installation  
It recommends using PLANET MGB-SX /  
MGB-LX series 1000Base-SX/LX SFP on the  
Notice:  
converter. If you insert a SFP transceiver  
that is not supported, the converter will  
not recognize it.  
15  
 
6.2 Chassis Installation and Rack Mounting  
To install the media converter in a 10-inch or 19-inch with  
standard rack, follow the instructions described below.  
Step 1: Place your GT-80X on a hard flat surface, with the  
front panel positioned towards your front side.  
Step 2: Carefully slide in the module until it is fully and  
firmly fitted into the slot of the chassis.  
Figure 6-3: Insert a media converter into an available slot  
Step 3: Attach a rack-mount bracket to each side of the  
Chassis with supplied screws attached to the  
package.  
Step 4: After the brackets are attached to the chassis, use  
suitable screws to securely attach the brackets to  
the rack, as shown in Figure 6-3.  
Step 5: Proceed with the steps 4 and steps 5 of session  
6.1 Stand-alone Installation to connect the  
network cabling and supply power to your switch.  
1ꢀ  
 
You must use the screws supplied with  
the mounting brackets. Damage caused to  
the parts by using incorrect screws would  
invalidate your warranty.  
Caution:  
1ꢁ  
 
Chapter 7 DUPLEX MODE SUPPORT  
The GT-80X is one-channel media conversion between  
10/100/1000Base-T and 1000Base-SX/LX. 10/100/1000Base-  
T port can work under Auto-negotiation mode. 1000Base-  
SX/LX fiber port only allow to work under fixed 1000Mbps  
full duplex mode.  
1ꢂ  
 
Chapter 8 LED INDICATION  
LED  
Color  
Description  
Lit: When +5VDC power  
detected.  
PWR  
Green  
Lit: To indicate the link through  
that fiber port is successfully  
established.  
Blink: Indicate that the Fiber  
port is actively sending or  
receiving data over that port.  
Fiber  
LNK/ACT  
Green  
Green  
Green  
Lit: To indicate the link through  
that port is successfully  
established.  
Blink: Indicate that the port is  
actively sending or receiving  
data over that port.  
TP  
LNK/ACT  
Lit: When the port runs in  
1000Mbps Full duplex.  
Blink: When the port runs in  
100Mbps Full duplex.  
TP  
1000  
Off: When the port runs in  
10Mbps Full duplex.  
Table 8-1: LED indication of GT-80x  
1ꢃ  
 
Chapter 9  
CABLE CONNECTION PARAMETER  
The wiring details are as below:  
Cables:  
Standard  
Fiber Type  
Cable Specification  
1000Base-SX  
(850nm)  
Multi-mode  
50/125μm or 62.5/125μm  
Multi-mode  
50/125μm or 62.5/125μm  
9/125μm  
1000Base-LX  
(1300nm)  
Single-mode  
Wiring Distances:  
Modal  
Bandwidth Distance  
(MHz * km) (meters)  
Max.  
Diameter  
(micron)  
Standard Fiber  
62.5  
62.5  
50  
100  
200  
400  
500  
220  
275  
500  
550  
1000Base-SX  
1000Base-LX  
MM  
50  
62.5  
50  
5
4
5
MM  
SM  
550  
50  
9
N/A  
5000*  
20  
 
The Single-mode port (1000Base-LX port)  
of GT-802S, GT-805A, GT-806A15/B15  
and GT-806A60/B60 is complied with LX 5  
kilometers and provides additional margin  
allowing for a 10/15/60 kilometers Gigabit  
Ethernet link on single mode fiber.  
Notice:  
21  
 
Chapter 10 PRODUCT SPECIFICATION  
The GT-80X comes with the following standard features:  
GT-806A15  
GT-806A60  
GT-806B15  
GT-806B60  
Model  
GT-802  
GT-802S  
GT-805A  
Connector  
– Fiber  
SFP, LC  
type  
SC-type connector  
SC-type connector (WDM) LX  
Multi-  
mode  
Single  
mode  
Vary on  
module  
Mode  
Single mode  
15km  
Single mode  
60km  
Fiber Maximum  
Distance  
220m /  
550m  
Vary on  
module  
10km  
Connector  
- Copper  
10/100/1000Mbps RJ-45  
Full Duplex, auto-negotiation  
Modes  
Packet  
14880 pps @10Mbps  
Forwarding  
Rate (64bytes)  
148810 pps @100Mbps  
1488000 pps @ 1000Mbps  
LED indicators:  
PWR, 1000, Fiber/LNK/ACT, TP/LNK/ACT  
IEEE 802.3 10Base-T  
Protocols and  
Standards:  
IEEE 802.3u 100Base-TX  
IEEE 802.3ab 1000Base-T  
IEEE 802.3z 1000Base-SX/LX  
22  
 
10/100/1000Base-T:  
1000Base-T-2-pair UTP Cat. 5/5e/6, up to 100m  
1000Base-SX:  
Cable  
50/125μm or 62.5/125μm multi-mode fiber optic cable, up to  
220/550m  
1000Base-LX:  
9/125μm single-mode fiber optic cable, up to 10/15/60km  
Dimensions  
Power  
26 x 70 x 97mm (H x W x D)  
External power adaptor 5V 2A max.  
EMI  
FCC Class A, CE Certification Class A  
Compatibility:  
Storage: -40°C ~ 70°C  
Operating: 0°C ~ 50°C  
Temperature:  
Humidity:  
5% ~90% non-condensing  
Connecting to the Gigabit Ethernet  
products, please refer to the device’s  
Technical Manual.  
Notice:  
23  
 
Chapter 11 POWER INFORMATION  
The power jack of GT-80X is with 2.5mm in the central post  
and required +5VDC power input. It will conform to the  
bundled AC-DC adapter and Planet’s Media Chassis. Should  
you have the problem to make the power connection, please  
contact your local sales representative.  
Please keep the AC-DC adapter as spare parts when your  
GT-80X is installed to a Media Chassis.  
24  
 
2010-AA4230-000  
 

Philips Battery Charger SCB1400NB User Manual
Philips Cassette Player AZ 6830 User Manual
Philips Computer Drive FM01FD05B User Manual
Philips Electric Toothbrush 300 Series User Manual
Philips Network Card Sdw1850 17 User Manual
Philips Stereo System SWA3604W User Manual
Philips Switch SWS4686W User Manual
Poulan Trimmer TE 400 LE User Manual
Powerware Power Supply P93 User Manual
Pride Mobility Mobility Aid Jazzy 1122 User Manual