Promise Technology Network Card TX4000 User Manual

FASTTRAK TX4000  
USER MANUAL  
Version 1.3  
 
Contents  
Chapter 1: Introduction........................................................................................ 1  
What is the FastTrak TX4000 RAID Card? .................................................. 1  
Promise Array Management Utility (PAM).................................................... 2  
Keys Features and Benefits......................................................................... 3  
Chapter 2: Quick Start......................................................................................... 5  
Installing the FastTrak TX4000 Card............................................................ 6  
Installing the Hard Drives............................................................................. 7  
Creating Your Disk Array.............................................................................. 9  
Creating an Array for Performance ............................................................ 10  
Creating a Security Array with New Drives................................................. 11  
Creating a Security Array with an Existing Data Drive .............................. 12  
Chapter 3: Using FastBuild Configuration  
Utility........................................... 15  
Viewing FastTrak TX4000 BIOS Screen.................................................... 15  
Navigating the FastBuild Setup Menu........................................................ 16  
Using the Main Menu.......................................................................... 16  
Creating Arrays Automatically.................................................................... 17  
Optimize Array for............................................................................... 18  
Defining Typical Application Usage..................................................... 18  
Using a Hot Spare Drive ..................................................................... 19  
Creating Multiple Disk Arrays.............................................................. 19  
Viewing Drive Assignments........................................................................ 20  
Manually Creating an Array........................................................................ 21  
Selecting Array Type........................................................................... 22  
Selecting Stripe Block......................................................................... 22  
Gigabyte Boundary ............................................................................. 23  
Assigning Drive(s) to Array ................................................................. 23  
Creating a Mirrored Array Using New Drives ...................................... 24  
Adding Fault Tolerance to an Existing Drive ....................................... 25  
Making a FastTrak TX4000 Disk Array Bootable ................................ 27  
Creating a Hot Spare Drive for Mirrored Arrays .................................. 28  
How FastTrak TX4000 Orders Arrays................................................. 28  
How FastTrak TX4000 Saves Array Information................................. 28  
Deleting an Array ....................................................................................... 29  
Rebuilding a Mirrored Array ....................................................................... 31  
Chapter 4: Installing Software Drivers............................................................... 33  
New Windows Server 2003 Installation...................................................... 34  
Existing Windows Server 2003 Installation................................................. 35  
Confirming Windows Server 2003 Driver Installation ................................. 35  
New Windows XP Installation..................................................................... 36  
Existing Windows XP Installation ............................................................... 37  
Confirming Windows XP Driver Installation................................................ 37  
New Windows 2000 Installation ................................................................. 38  
iii  
 
FastTrak TX4000 User Manual  
Existing Windows 2000.............................................................................. 39  
Confirming Windows 2000 Driver Installation............................................. 39  
New Windows ME Installation.................................................................... 40  
Existing Windows ME Installation............................................................... 41  
Confirming Driver Installation in Windows ME............................................ 41  
New Windows NT4.x Installation................................................................ 42  
Existing Windows NT4.x Installation .......................................................... 43  
Removing the Driver from Windows NT4.x ................................................ 43  
New Windows 98 Installation ..................................................................... 44  
Existing Windows 98 Installation................................................................ 45  
Confirming Driver Installation in Windows 98............................................. 45  
Chapter 5: Disk Array Concepts........................................................................ 47  
About FastTrak TX4000............................................................................. 47  
About Adapter BIOS ........................................................................... 47  
FastBuild Auto Menu Setup ................................................................ 47  
Reserved Sector ................................................................................. 47  
Disk Array Terms ....................................................................................... 48  
Disk Array Description......................................................................... 48  
Disk Array Member ............................................................................. 48  
Disk Array Types................................................................................. 48  
About RAID Levels..................................................................................... 49  
Striping (RAID 0)................................................................................. 49  
Mirroring (RAID 1)............................................................................... 50  
Striping / Mirror (RAID 0+1) ................................................................ 51  
About Dual Data Redundancy............................................................. 52  
Chapter 6: Troubleshooting & Tips.................................................................... 53  
Motherboard Issues ................................................................................... 53  
System CMOS Issues................................................................................ 54  
Drive-Related Errors .................................................................................. 55  
Operating System-Related Issues.............................................................. 58  
Performance Tips....................................................................................... 60  
Appendix A: Frequently Asked Questions......................................................... 63  
Pre-Installation ........................................................................................... 63  
Drive Issues ............................................................................................... 64  
Installation Issues....................................................................................... 66  
Post-Installation.......................................................................................... 66  
Appendix B: Technical Support......................................................................... 67  
Technical Support Services........................................................................ 67  
Limited Warranty........................................................................................ 69  
Returning Product for Repair...................................................................... 71  
iv  
 
Chapter 1: Introduction  
The PC which you are using either already contains a Promise Technology  
FastTrak TX4000 RAID card installed by a third-party or you have acquired a  
FastTrak TX4000 retail product for your existing PC and will be installing the  
card yourself.  
For PC owners wishing to install their Promise Technology FastTrak  
TX4000 card, proceed to Chapter 2: Quick Start on page 5.  
For PCs with a Promise Technology FastTrak TX4000 card already  
installed, consult Chapter 6: Troubleshooting and Tips on page 51 if you are  
experiencing any difficulties with the hard drive being recognized by the  
card.  
If your operating system has crashed for some reason or you have  
downloaded updated drivers from the Promise website (www.promise.com),  
you may wish to reinstall software drivers for the FastTrak TX4000 card.  
Consult Chapter 4: Installing Drivers on page 33.  
What is the FastTrak TX4000 RAID Card?  
Promise originally designed the FastTrak TX4000 card as a cost-effective, high  
performance RAID card that adds performance and/or reliability to PC desktops  
and/or servers using Ultra ATA/133, Ultra ATA/100, or Ultra ATA/66 drives. The  
FastTrak TX4000 offer some major performance differences as described below.  
The FastTrak TX4000 supports motherboards that offer a 66MHz PCI bus  
(versus the traditional 33MHz bus) and the capability of transferring data across  
the PCI bus at speeds up to 266MB per second (versus the previous 133MB per  
second). As Ultra ATA/133 drive performance continues to improve, the use of  
the Promise ATA RAID card in a 66 MHz PCI slot will allow data transfers to  
exceed the older 33MB. Of course, the FastTrak TX4000 is backward  
compatible with standard 33MHz PCI slots.  
FastTrak TX4000 has four independent data channels to support a maximum of  
four Ultra ATA drives. FastTrak TX4000 supports striping (RAID 0), mirroring  
(RAID 1) or striping/mirroring (RAID 0+1).  
With striping, identical drives can read and write data in parallel to increase  
performance.  
Mirroring increases read performance through load balancing and elevator  
sorting while creating a complete backup of your files.  
Striping with mirroring offers both high read/write performance and fault  
tolerance.  
A FastTrak TX4000 striped array can double the sustained data transfer rate of  
Ultra ATA/133 drives. FastTrak TX4000 fully supports Ultra ATA/133  
specification of up to 133 MB/sec per drive, depending on individual drive  
specifications.  
1
 
FastTrak TX4000 User Manual  
All FastTrak TX4000 models also offer fault tolerant, data redundancy for entry-  
level network file servers or simply for desktop PC users wanting to continually  
protect valuable data on their PC. Each FastTrak TX4000 model offers RAID 1  
mirroring (for two drives) and RAID 0+1 mirroring plus striping (for four drives) to  
protect data. Should a drive that is part of a mirrored array fail, FastTrak TX4000  
uses the mirrored drive (which contains identical data) to assume all data  
handling. When a new replacement drive is later installed, FastTrak TX4000  
rebuilds data to the new drive from the mirrored drive to restore fault tolerance.  
When attached drives are used with optional Promise SuperSwap series hot  
swap chassis, the FastTrak TX4000 allows replacing a failed drive without  
shutting down the PC operation under RAID 1 mirroring.  
FastTrak TX4000’s bootable BIOS supports individual drives larger than 137  
GB. With FAT32 and NTFS partitioning, the array can be addressed as one  
large single volume.  
Promise Array Management Utility (PAM)  
Professional RAID array management utility offers local and remote  
management and monitoring of all FastTrak arrays that exist anywhere on a  
network. Windows-based GUI provides email notification of all major  
events/alarms, memory cache management, logging for NT/2000 servers, array  
maintenance, rebuild, and access to all components in array (server, controller,  
data channels, individual drives, and enclosure). For information on using PAM,  
refer to the PAM User Manual, which is included in the FastTrak TX4000  
package.  
2
 
Chapter 1: Introduction  
Keys Features and Benefits  
The following information offers an overview of the major features of your new  
Promise FastTrak TX4000 card...  
Advanced Hardware Design  
Features  
Benefits  
Supports 66MHz PCI bus  
motherboards (automatically  
backward compatible with  
33MHz PCI slots)  
Allows maximum data transfers of up to  
266MB per second (133 MB/s in 33 MHz  
slot) over the bus to dramatically reduce the  
time to save and retrieve large files.  
Supports data striping (RAID  
0), mirroring (RAID 1), and  
striping/mirroring combination  
(RAID 0+1)  
Provides dramatic increase in drive  
performance and/or fault tolerant options.  
Offers performance customization and data  
rebuilds from the BIOS menu.  
Supports  
Ultra DMA 6/5/4  
DMA 2/1/0  
Burst data transfer rates up to 133MB/sec  
from Ultra ATA/133 drives to boost overall  
system performance.  
Drives can multiply their data transfer  
performance when striped together and  
each drive uses a separate data channel.  
Independent data channels  
PCI Plug-n-Play, PCI Interrupt  
sharing and coexists with  
motherboard IDE controllers  
Easy to install; support four ATA drives on  
the FastTrak TX4000 while still supporting 4  
devices on motherboard ATA controller.  
Supports concurrent IDE  
channel operation  
Drive workload is distributed in parallel  
between members of the array.  
Allows multitasking during disk transfers  
that increase CPU efficiency. The CPU is  
free to process tasks during IDE data  
transfers through the PCI Bus to/from  
system memory.  
Supports IDE bus master  
operation  
Offers pre-set application specific settings  
that can be optimized for Desktop, Server,  
or A/V Editing. Has Auto Setup option for  
quick and easy array builds.  
Utilizes FastBuild automenu  
from the FastTrak TX4000  
onboard BIOS  
Displays status and error  
checking messages during  
boot up  
Notifies user of possible errors and allows  
for recovery of mirrored drive arrays directly  
from FastBuild.  
Fully supports Ultra ATA/133 specifications  
with 133 MB/sec timing and CRC error-  
checking at high speeds.  
Employs the latest Promise PCI  
Ultra ATA/133 ASIC technology  
3
 
FastTrak TX4000 User Manual  
Mirroring supports automatic  
background rebuilds  
Fault tolerance can be restored  
automatically without rebooting.  
Compatibility  
Benefits  
Features  
Complies with PCI v2.2 Local  
Bus standard  
Provides highest level of hardware  
compatibility.  
Compliant with PCI IDE Bus  
Master standard. PCI IDE Bus  
Provides 32-bit I/O, IDE Bus Master, and  
Master support for Windows 98, Ultra ATA performance for optimal system  
ME, NT4, 2000, XP, Server  
2003  
performance.  
Tested compatibility to coexist  
with motherboards that have  
integrated IDE controllers  
Improves system performance of new and  
existing installations including  
motherboards with Intel chipsets.  
Works with newest and current IDE drive  
specifications. Promise engineers  
experienced with IDE devices perform  
verification testing with major drive  
manufacturers and development partners.  
Compatible with Ultra ATA/133,  
Ultra ATA/100, Ultra ATA/66  
drives supporting multi-word  
DMA  
Breaks capacity barriers for support of  
drives greater than 137 GB in capacity.  
Offers flexible storage options for space  
demanding applications.  
Features LBA and Extended  
Interrupt13 drive translation in  
controller onboard BIOS  
4
 
Chapter 2: Quick Start  
When you receive the FastTrak TX4000 Series Controller Card, the package  
should contain the items listed below:  
FastTrak TX4000 Ultra ATA/133 RAID Controller Card  
Quick Start Guide  
FastTrak TX4000 driver diskette  
Two Y-cable power splitters.  
Four internal 80-wire/40-pin Ultra ATA/133 hard drive cables (18 inches or  
45 cm in length)  
CD with Promise Array Management (PAM) utility, PAM User Manual and  
FastTrak TX4000 User Manual.  
If ANY of the contents are missing or appear to be damaged, please contact  
your dealer or distributor immediately.  
Warning  
Before installing the adapter into an existing system, backup any  
important or useful data. Failure to follow this accepted PC  
practice could result in data loss.  
Warning  
The FastTrak TX4000 Controller card, like other parts of your  
system, is subject to damage by static electricity. Be sure that  
you’re properly grounded (Promise recommends that you wear  
an anti-static strap or touch a grounded object) and that you  
unplug your system before installing your FastTrak TX4000  
Controller card.  
5
 
FastTrak TX4000 User Manual  
Installing the FastTrak TX4000 Card  
The FastTrak TX4000 Controller card fits into any available 32-bit PCI slot (must  
be PCI 2.1 or 2.2 compliant). It also fits the 32-bit portion of a 64-bit PCI slot, on  
the system’s motherboard (see figure below).  
1. Remove the cover of your system.  
2. Remove the inside slot cover of an available 32-bit PCI slot on the  
motherboard.  
3. Install the FastTrak TX4000 Controller card into the open slot (see Figure 1  
below). Secure the bracket to the system’s frame.  
4. Attach your system case’s 2- or 4-pin LED cable to the LED connector on  
the FastTrak TX4000 Controller card (see Figures 2 and 3, below). Make  
sure that pin 1 on the connector is aligned with pin 1 of the cable.  
5. Fasten the controller card bracket to the system case (see below).  
Figure 1. Insert the FastTrak TX4000 card into an open PCI slot.  
6
 
Chapter 2: Quick Start  
Installing the Hard Drives  
Important  
If you wish to include your current bootable ATA drive using the  
Windows NT4.x, 2000, XP, Server 2003, ME or 98 operating  
system on your FastTrak TX4000 Controller card, do NOT  
connect the hard drive to the card yet.  
You MUST install the Windows NT4.x, 2000, XP, Server 2003,  
ME or 98 driver software first onto this drive while it is still  
attached to your existing hard drive controller.  
Hard drives must be Ultra ATA/133, Ultra ATA/100, Ultra ATA/66 compatible to  
operate with the FastTrak TX4000 RAID Adapter. For optimal performance,  
install all identical drives of the same model and capacity. The drives’ matched  
performance allows the array to function better as a single drive.  
1. Promise recommends using identical drives as part of a FastTrak TX4000  
array. If striping for performance, use up to four new drives. If mirroring for  
protection, you can use two new drives OR use an existing drive and a new  
drive (the new drive must be the same size or larger than the existing drive).  
2. Set the jumpers on all drives to Master, Cable Select in Master position or  
Single.  
3. Install the hard drives into the hard drive bays of your system, including the  
power cables.  
Warning  
Use of removable hard drive enclosures other than Promise  
Technology’s SuperSwap series is not supported and may result  
in performance loss or other undesired results.  
4. Attach a black connector of the Ultra ATA cable to each hard drive.  
5. Attach a blue cable connector to each of the IDE connectors on the  
FastTrak TX4000 controller card. The black colored edge of the cable(s)  
indicates Pin 1 (see Figure 2).  
7
 
FastTrak TX4000 User Manual  
IDE 2  
IDE 1  
IDE 3  
IDE 4  
LED Pin 1  
Figure 2. TX4000 card  
Important  
You must use an 80-wire, 40-pin cable when connecting your  
hard drives to the FastTrak TX4000 controller card. The  
FastTrak TX4000 package contains four 80-wire, 40-pin cables.  
Notes  
The FastTrak TX4000 Controller card is a PCI Plug-n-Play  
(PnP) device. No changes are necessary in the Motherboard  
CMOS Setup for resources or drive types in most  
applications.  
If you wish to boot from a FastTrak TX4000 drive array AND  
continue to use hard drives attached to your motherboard’s  
IDE controller, refer to your motherboard manual for the  
specific BIOS settings to use in order to establish their  
proper boot order.  
8
 
Chapter 2: Quick Start  
Creating Your Disk Array  
You will now use the onboard FastBuild BIOS utility to create your array using  
the attached drives. There are three different scenarios in creating this array.  
You can create an array for performance, you can create a Security array using  
new hard drives (recommended), or you can create a Security array using an  
existing hard drive and a new hard drive.  
Warning  
If creating a Security array using an existing hard drive, backup  
any necessary data. Failure to follow this accepted PC practice  
could result in data loss.  
Boot your system. If this is the first time you have booted with the FastTrak  
TX4000 card and drives installed, the Promise onboard BIOS will display the  
following screen.  
FastTrak TXx000 (tm) BIOS Version 1.xx (Build xxxx)  
(c) 2002-2005 Promise Technology, Inc. All Rights Reserved.  
No array defined . . .  
Press <Ctrl-F> to enter FastBuild (tm) Utility  
Or press <ESC> key to continue booting the system.  
Press the Ctrl-F keys to display the FastBuild Utility Main Menu.  
Press “1” to display the Auto Setup Menu below. This is the fastest and easiest  
method to creating your first array.  
9
 
FastTrak TX4000 User Manual  
FastBuild (tm) Utility 1.xx (c) 2002-2005 Promise Technology, Inc.  
[Auto Setup Options Menu]  
Optimize Array for:  
Typical Application usage:  
Performance  
A/V Editing  
[ Auto Setup Configuration ]  
Mode...........................................................Stripe  
Drives used in Array........................................... 2  
Array Disk Capacity.................................... 16126  
[ Keys Available ]  
[] Up [] Down [, , Space] Change Option [ESC] Exit [Ctrl-Y] Save  
Note  
If you wish to customize certain settings at a later time, you  
may do so by manually creating your array. See Using  
FastBuild Configuration Utility on page 15.  
Creating an Array for Performance  
FastTrak TX4000 allows users to create striped or mirrored arrays with 1, 2, 3,  
or 4 drives.  
To create an array for best performance, follow these steps:  
1. Using the Spacebar, choose Performance under the Optimize Array for  
section.  
2. Select how you will use your PC most under the Typical Application usage  
section. The choices are A/V Editing, Server, and Desktop (the default).  
3. Press Ctrl-Y to Save and create the array.  
4. Reboot your system.  
5. Once the array has been created, you will need to FDISK and format the  
array as if it were a new single hard drive.  
6. Proceed to Chapter 4: Installing Drivers.  
10  
 
Chapter 2: Quick Start  
Creating a Security Array with New Drives  
Notes  
Under the Security setting, FastTrak TX4000 permits two  
drives to be used for a single Mirrored array or four drives to  
be used for a Mirrored/Striped array in Auto Setup.  
When creating a Security array with new drives, a feature  
called Gigabyte Boundary will automatically be set to ON.  
For a description of the Gigabyte Boundary feature, see  
page 23.  
To create an array for data protection using new hard drives, follow these steps:  
1. Using the Spacebar, choose Security under the Optimize Array for section.  
2. Press Ctrl-Y to Save your selection.  
3. The window below will appear.  
Do you want the disk image to be duplicated to another? (Yes/No)  
Y - Create and Duplicate  
N - Create Only  
4. Press N for the Create Only option.  
5. A window will appear almost immediately confirming that your Security array  
has been created. Press any key to reboot the system.  
Array has been created.  
<Press Any Key to Reboot>  
6. Proceed with normal FDISK and format procedures as if you had just  
installed a new hard drive.  
7. Once the arrayed drives have been formatted, proceed to Chapter 4 to  
install your operating system and/or FastTrak TX4000 driver.  
11  
 
FastTrak TX4000 User Manual  
Creating a Security Array with  
an Existing Data Drive  
Under the Security setting, FastTrak TX4000 permits two drives to be used for a  
single Mirrored array or four drives to be used for a Mirrored/Striped array in  
Auto Setup.  
You would use this method if you wish to use a drive that already contains data  
and/or is the bootable system drive in your system. You will need another drive  
of identical or larger storage capacity.  
Warning  
If creating a Security array using an existing hard drive, backup  
any necessary data. Failure to follow this accepted PC practice  
could result in data loss.  
Warning  
If you wish to include your current bootable drive using the  
Windows NT 4.x, 2000, XP, Server 2003, ME or 98 operating  
system as part of a bootable Mirrored (RAID 1) array on your  
FastTrak TX4000, do NOT connect the hard drive to the  
FastTrak TX4000 controller yet.  
You MUST install the Windows NT 4.x, 2000, XP, Server 2003,  
ME or 98 driver software first (see Chapter 4) to this drive while it  
is still attached to your existing hard drive controller.  
Follow these steps:  
1. Using the Spacebar, choose Security under the Optimize Array for section.  
2. Press Ctrl-Y to Save your selection. The window below will appear.  
Do you want the disk image to be duplicated to another? (Yes/No)  
Y - Create and Duplicate  
N - Create Only  
3. Press Y for the Create and Duplicate option. The window below will appear  
asking you to select the Source drive to use. FastBuild will copy all data  
from the Source drive to the Target drive.  
12  
 
Chapter 2: Quick Start  
Source Disk  
Drive Model  
Channel: Drive ID  
Channel: Drive ID  
Channel: Drive ID  
Capacity (MB)  
Target Disk  
Drive Model  
Capacity (MB)  
[Please Select A Source Disk]  
Drive Model  
Capacity (MB)  
8063  
1 :  
3 :  
1
3
QUANTUMCR8.4A  
QUANTUMCR8.4A  
8063  
[] Up [] [ESC] Exit [Ctrl-Y] Save  
4. Press the arrow keys to choose which drive contains the existing data to be  
copied.  
5. Press Ctrl-Y to Save selection and start duplication. The following progress  
screen will appear.  
Start to duplicate the image . . .  
Do you want to continue? (Yes/No)  
Y – Continue N - Abort  
6. Select Y to continue. If you choose N, you will be returned to step 1.  
7. Once complete, the following screen will appear confirming that your  
Security array has been created. Press any key to reboot the system.  
Array has been created.  
<Press Any Key to Reboot>  
8. Proceed to Chapter 4: Installing Drivers to install the FastTrak TX4000  
driver and/or operating system.  
13  
 
FastTrak TX4000 User Manual  
14  
 
Chapter 3: Using FastBuild Configuration  
Utility  
The FastBuild Configuration Utility offers several menu choices to create and  
manage the drive array on the Promise FastTrak TX4000 adapter. For purposes  
of this manual, it is assumed you have already created an array in the previous  
chapter and now wish to make a change to the array or view other options.  
Viewing FastTrak TX4000 BIOS Screen  
When you boot your system with the FastTrak TX4000 card and drives installed,  
the Promise onboard BIOS will detect the drives attached and show the  
following screen.  
FastTrak TXx000 (tm) BIOS Version 1.xx (Build xxxx)  
(c) 2002-2005 Promise Technology, Inc. All Rights Reserved.  
Scanning IDE drives . . . . .  
If an array exists already, the BIOS will display the following screen showing the  
card’s BIOS version and status of the array.  
FastTrak TXx000 (tm) BIOS Version 1.xx (Build xxxx)  
(c) 2002-2005 Promise Technology, Inc. All Rights Reserved.  
ID  
MODE  
SIZE  
TRACK-MAPPING  
611/128/32  
STATUS  
1 *  
2+0 Stripe  
16126M  
Functional  
Press <Ctrl-F> to enter FastBuild (tm) Utility....  
The array status consists of three possible conditions: Functional, Critical,  
Offline.  
Functional – The array is operational.  
Critical – A mirrored array contains a drive that has failed or disconnected. The  
remaining drive member in the array is functional. However, the array has  
temporarily lost its ability to provide fault tolerance. Use the FastBuild Setup  
utility to identify the failed drive. Then replace the drive.  
Offline – A mirrored array has two drives that have failed or become  
disconnected or a striped array has one drive that has failed or been  
disconnected. When the array condition is offline, you must replace the failed  
drive(s) and then restore data from a backup source.  
15  
 
FastTrak TX4000 User Manual  
Navigating the FastBuild Setup Menu  
When using the menus, these are some of the basic navigation tips: Arrow keys  
highlights through choices; the Space bar allows to cycle through options; Enter  
selects an option; Esc aborts or exits the current menu.  
Using the Main Menu  
This is the first option screen when entering the FastBuild Setup.  
FastBuild (tm) Utility 1.xx (c) 2002-2005 Promise Technology, Inc.  
[ Main Menu ]  
Auto Setup  
View Drive Assignments  
Define Array  
Delete Array  
Rebuild Array  
[ 1 ]  
[ 2 ]  
[ 3 ]  
[ 4 ]  
[ 5 ]  
[ Keys Available ]  
Press 1...5 to Select Option [ESC] Exit  
To create a new array automatically, follow the steps under Creating Arrays  
Automatically on page 17. Promise recommends this option for most users.  
To manually create an array or define an array as bootable, follow the steps  
under Manually Creating an Array on page 21.  
You will also need to manually create an array if you wish to modify block size.  
To make an existing array bootable, see page 27.  
To view drives assigned to arrays, see Viewing Drive Assignments on page 20.  
To delete an array (but not delete the data contained on the array), see Deleting  
an Array on page 29.  
To rebuild a mirrored array, see Rebuilding an Array on page 31.  
Notes  
After you install the FastTrak TX4000 card and configure an  
array using FastBuild, use FDISK to format the arrayed  
drive(s) if you are using new, blank drives.  
16  
 
Chapter 3: FastBuild Configuration Utility  
Creating Arrays Automatically  
The Auto Setup (1) selection from the Main Menu can intuitively help create your disk  
array. It will assign all available drives appropriate for the disk array you are creating.  
After making all selections, press Ctrl-Y to Save the selections. FastBuild will  
automatically build the array.  
FastBuild (tm) Utility 1.xx (c) 2002-2005 Promise Technology, Inc.  
[Auto Setup Options Menu]  
Optimize Array for:  
Performance  
Typical Application usage: A/V Editing  
[ Auto Setup Configuration ]  
Mode..............................................................Stripe  
Spare Drive Count ................................................ 1  
Drives used in Array ............................................. 2  
Array Disk Capacity (size in MB) .................. 16126  
[ Keys Available ]  
[] Up [] Down [, , Space] Change Option [ESC] Exit [Ctrl-Y] Save  
17  
 
FastTrak TX4000 User Manual  
Optimize Array for  
Select whether you want Performance (RAID 0), Security (RAID 1 or RAID 0+1)  
under the Optimize Array for setting.  
Performance  
RAID 0 (Striping) supports the high performance. The storage capacity equals  
the number of drives times the capacity of the smallest drive in the disk array.  
Note  
FastTrak TX4000 permits striped arrays using 1, 2, 3, or 4  
drives attached in Auto Setup mode.  
Under the Security setting, FastTrak TX4000 permits two  
drives to be used for a single Mirrored array or four drives  
to be used for a Mirrored/Striped array in Auto Setup.  
Security  
(RAID 1 Mirroring, or RAID 0+1 Striping/ Mirroring) creates a mirrored (or fault  
tolerant) array for data security. The storage capacity equals one-half the  
number of drives times the capacity of the smallest drive in the disk array.  
Note  
Under the Security setting, FastTrak TX4000 permits two  
drives to be used for a single Mirrored array or four drives  
to be used for a Mirrored/Striped array in Auto Setup.  
Security and Performance  
RAID 0+1 (Striping/Mirroring) creates an array with striping for high performance  
plus mirroring for fault tolerance and data security. The storage capacity equals  
one-half the number of drives times the capacity of the smallest drive in the disk  
array. This option requires 4 drives.  
Defining Typical Application Usage  
Allows the user to choose the type of PC usage that will be performed in order to  
optimize how FastTrak TX4000 handles data blocks to enhance performance.  
Your choice will determine the block size used. You may choose from: A/V  
Editing (for audio/video applications, or any similar application that requires  
large file transfers), Server (for numerous small file transfers), or Desktop (a  
combination of large and small file sizes).  
18  
 
Chapter 3: FastBuild Configuration Utility  
Using a Hot Spare Drive  
If a third drive is attached and is not assigned to a mirrored two-drive disk array  
(one optimized for Security), it will be recognized as a spare drive. Such a drive  
is immediately used as a standby replacement. It is automatically added to an  
array once a disk member of the array has been detected as failed.  
To restore fault tolerance as quickly as possible, FastTrak TX4000 begins to  
perform an automatic data rebuild on the spare drive in the background without  
the need to restart the system.  
At a later time, the failed drive can be physically removed from the FastTrak  
TX4000 card and an extra drive added in its place to function as the spare drive.  
Important  
The hot spare drive must have a capacity that is equal to or  
larger than the smallest array member.  
Creating Multiple Disk Arrays  
If you plan to create multiple arrays,  
1. Attach only the drives necessary to create the first disk array and complete  
the Auto Setup (1).  
2. Install the additional drives needed for the second array and again use the  
Auto Setup (1).  
Note  
If you wish to customize the settings of individual disk  
arrays (such as block size), you must manually create disk  
arrays with the Define Array (3) option from the Main Menu.  
19  
 
FastTrak TX4000 User Manual  
Viewing Drive Assignments  
The View Drive Assignments (2) option in the Main Menu displays whether  
drives are assigned to a disk array or are unassigned.  
Under the Assignment column, drives are labeled with their assigned disk array  
or shown as Free if unassigned. Such Free drives can be used for a future array  
or used as a spare drive when a drive fails in a mirrored array, provided the free  
drive’s capacity is equal to or larger than the smallest array member.  
Unassigned drives are not accessible by the OS. The menu also displays the  
data transfer mode that relates to speed used by each drive (U5 refers to  
100MB/sec transfers, U4 refers to 66MB/sec transfers, etc...)  
FastBuild (tm) Utility 1.xx (c) 2002-2005 Promise Technology, Inc.  
[ View Drive Assignments ]  
Channel: Drive ID  
Drive Model  
Capacity(MB) Assignment Mode  
1 :  
2 :  
3 :  
4 :  
1
2
3
QUANTUMCR8.4A  
QUANTUMCR8.4A  
QUANTUMCR8.4A  
8063  
8063  
8063  
Array 1  
Free  
Array 1  
U5  
U5  
U5  
[ Keys Available ]  
[] Up [] Down [ESC] Exit Mode (U=UDMA, P=PIO, D=DMA)  
20  
 
Chapter 3: FastBuild Configuration Utility  
Manually Creating an Array  
The Define Array (3) option from the Main Menu allows users to begin the  
process of manually defining the drive elements and RAID levels for one or  
multiple disk arrays attached to FastTrak TX4000.  
Users will commonly create one or two drive arrays with FastTrak TX4000,  
though the card will support a maximum of four arrays. You may use a single  
drive in striping mode with FastTrak TX4000. In this rare scenario, the card will  
create an individual array ID but will offer conventional controller performance  
depending on the drive type. At a later time, you can add a second drive to the  
array and recreate the array to support RAID 1 mirroring.  
Note  
For most installations, Promise recommends the (1) Auto  
Setup for easy disk array creation.  
FastBuild (tm) Utility 1.xx (c) 2002-2005 Promise Technology, Inc.  
[Define Array Menu]  
Array No  
Array 1  
Array 2  
Array 3  
Array 4  
RAID Mode  
Stripe  
——  
Total Drv  
2
——  
——  
——  
Capacity(MB)  
16126  
——  
Status  
Functional  
——  
——  
——  
——  
——  
——  
——  
[ Keys Available ]  
Note: * — Bootable Array  
[] Up [] Down [ESC] Exit [Enter] Select [Space] Change Boot Drive  
To manually create an array from the Define Array Menu:  
1. Press the arrow keys to highlight the array number you wish to define, and  
press Enter to select.  
2. The Define Array Definition Menu will next appear that allows drive  
assignments to the disk array (see next page).  
21  
 
FastTrak TX4000 User Manual  
Selecting Array Type  
1. Under the Definition section of this menu, highlight the Array # for which you  
want to assign a RAID level.  
2. Press the Spacebar to cycle through three array types:  
Performance (RAID 0 Striping)  
Security (RAID 1 Mirroring  
RAID 0+1 Striping/Mirroring (for 4 drives)  
See page 50 for more information about RAID levels.  
FastBuild (tm) Utility 1.xx (c) 2002-2005 Promise Technology, Inc.  
[ Define Array Definition Menu ]  
Array No  
Array 1  
RAID Mode  
Stripe  
Total Drv  
2
Capacity(MB)  
16126  
Status  
Functional  
Stripe Block: 64 KB  
Gigabyte Boundary: ON  
[ Drive Assignments ]  
Channel: Drive ID  
Drive Model  
Capacity (MB) Assignment  
1 :  
2 :  
3 :  
4 :  
1
2
3
QUANTUMCR8.4A  
QUANTUMCR8.4A  
QUANTUMCR8.4A  
8063  
8063  
8063  
Y
N
Y
[ Keys Available ]  
[] Up [] Down [ESC] Exit [Space] Select [Ctrl-Y] Save  
Selecting Stripe Block  
For RAID 0 and RAID 0+1 arrays you may manually select the stripe block size.  
Press the Spacebar to scroll through choices progressing as follows (16, 32, 64,  
128, 256 MB).  
The size selected affects how FastTrak TX4000 sends and retrieves data blocks  
to and from the drives. You will need to perform your own testing to determine  
how the data block size is affecting your particular use of the array. In general, a  
larger block size is better when handling large data transfers (such as in A/V  
editing or graphics) while a smaller block size is better when handling e-mail and  
other common server data. The default is 64K.  
22  
 
Chapter 3: FastBuild Configuration Utility  
Gigabyte Boundary  
The Gigabyte Boundary feature is designed for mirrored arrays (RAID 1 or RAID  
0+1) in which a drive has failed and the user cannot replace the drive with the  
same capacity or larger. Instead, the Gigabyte Boundary feature permits the  
installation of a replacement drive that is slightly smaller (within 1 gigabyte) than  
the remaining working drive (for example, an 80.5 GB drive would be rounded  
down to 80 GB).  
This can be helpful in the event that a drive fails and an exact replacement  
model is no longer available. Without this feature enabled, FastTrak TX4000 will  
NOT permit the use of a replacement drive that is slightly smaller than the  
remaining working drive.  
For the Gigabyte Boundary feature to work, the Gigabyte Boundary feature must  
be set to ON when the original mirrored array is created. When enabled, the  
Gigabyte Boundary feature rounds the drive capacity of both drives to the  
common whole GB drive size. For example, with the Gigabyte Boundary feature  
enabled, the remaining working drive can be 80.5 GB and the replacement drive  
can be 80.3, since both are rounded down to 80GB.  
This permits the smaller drive to be used. Please note that users will lose a  
small amount of available storage capacity from both drives in order to arrive at  
a common drive size.  
Note  
Gigabyte Boundary is automatically disabled when creating  
a mirrored array (RAID 1) from an existing drive (versus  
using two brand new drives). This protects the existing  
drive’s partition table in order to maintain data integrity.  
Assigning Drive(s) to Array  
1. Under the Drive Assignments section, highlight a drive by pressing the ↑  
and keys.  
2. Press the Spacebar to change the Assignable option to Y to add the drive to  
the disk array.  
3. Press Ctrl-Y to save the disk array information. Depending on the array type  
selected, the following scenarios will take place:  
If choosing a Striping or Mirroring/Striping array, the initial Define Array  
Menu screen will appear with the arrays defined. From there you may  
ESC to exit and return to the Main Menu of FastBuild.  
If you selected a Mirroring array for two drives, there is an additional  
window that appears as described in order to create the array. To do  
this you will use either two brand new drives, or one drive that contains  
existing data that you wish to mirror.  
23  
 
FastTrak TX4000 User Manual  
Creating a Mirrored Array Using New Drives  
As described in the Drive Assignments Option section above, if you selected a  
mirroring array and wish to use two new assigned drives, follow the directions  
here.  
1. Assign new drives to a Mirroring array  
2. Save the information by pressing Ctrl-Y, the window below will appear.  
Do you want the disk image to be duplicated to another? (Yes/No)  
Y - Create and Duplicate  
N - Create Only  
3. Press N for the Create Only option. A window will appear almost  
immediately confirming that your Security array has been created.  
Array has been created.  
<Press Any Key to Reboot>  
4. Press any key to reboot the system.  
24  
 
Chapter 3: FastBuild Configuration Utility  
Adding Fault Tolerance to an Existing Drive  
FastTrak TX4000 will create a mirrored array using an existing system drive with  
data. You must assign the existing drive and another drive of same or larger  
capacity to the Mirroring array. The BIOS will send the existing data to the new  
blank drive.  
Warning  
Backup any necessary data before proceeding. Failure to  
follow this accepted PC practice could result in data loss.  
Warning  
If you wish to include your current bootable drive using the  
Windows NT 4.x, 2000, XP, Server 2003, ME or 98  
operating system as part of a bootable Mirrored (RAID 1)  
array on your FastTrak TX4000, You MUST install the  
driver software while the bootable drive is still attached to  
your existing hard drive controller. See Chapter 4.  
1. Assign the drives to a Mirroring array.  
2. Press Ctrl-Y to Save your selection. The window below will appear.  
Do you want the disk image to be duplicated to another? (Yes/No)  
Y - Create and Duplicate  
N - Create Only  
Note  
Gigabyte Boundary is automatically disabled when creating  
a mirrored array (RAID 1) from an existing drive (versus  
using two brand new drives). This protects the existing  
drive’s partition table in order to maintain data integrity.  
3. Press Y for the Create and Duplicate option. The window below will appear  
asking you to select the Source drive to use. FastBuild will copy all data  
from the Source drive to the Target drive.  
25  
 
FastTrak TX4000 User Manual  
Source Disk  
Drive Model  
Channel: Drive ID  
Channel: Drive ID  
Capacity (MB)  
Capacity (MB)  
Target Disk  
Drive Model  
[Please Select A Source Disk]  
Channel: Drive ID  
Drive Model  
QUANTUMCR8.4A  
QUANTUMCR8.4A  
Capacity (MB)  
8063  
1 :  
3 :  
1
3
8063  
[] Up [] [ESC] Exit [Ctrl-Y] Save  
4. Press the arrow keys to choose which drive contains the existing data to be  
copied.  
Warning  
All target drive data will be erased. Make sure you choose  
the correct drive.  
5. Press Ctrl-Y to Save selection and start duplication. The following  
confirmation screen will appear.  
Start to duplicate the image . . .  
Do you want to continue? (Yes/No)  
Y – Continue N - Abort  
6. Select Y to continue. If you choose N, you will be returned to step 1.  
7. Once you select Y, the following progress screen will appear. The process  
will take a few minutes.  
Please Wait While Duplicating The Image  
10%  
Complete  
Once mirroring is complete, the following screen will appear confirming that  
your Security array has been created.  
Array has been created.  
<Press Any Key to Reboot>  
8. Press any key to reboot the system.  
26  
 
Chapter 3: FastBuild Configuration Utility  
Making a FastTrak TX4000 Disk Array Bootable  
Warning  
If you plan to boot from an array on the FastTrak TX4000,  
you must configure the system BIOS Setup to use the  
FastTrak TX4000 as a bootable device (rather than the  
onboard controller or another add-in card).  
This option is not available if the FastTrak TX4000 is being  
used as a secondary controller.  
Once you have returned to the Define Array Menu window (below), you will see  
the array(s) you have created. You now may use the menu to select which  
previously-defined array will be used as the bootable array.  
FastBuild (tm) Utility 1.xx (c) 2002-2005 Promise Technology, Inc.  
[ Define Array Menu ]  
Array No  
* Array 1  
RAID Mode  
Stripe  
Total Drv  
2
Capacity(MB)  
13044  
Status  
Functional  
Note: * — Bootable Array  
[] Up [] Down [ESC] Exit [Enter] Select [Space] Change Boot Drive  
1. Highlight the array that you want to boot from using the Up Down keys.  
2. Press the Spacebar.  
3. An asterisk (*) appears next to the array number indicating it as bootable.  
The system will now recognize this array as the first array seen.  
4. The system will then use this bootable array as the (fixed) boot C: drive.  
Note  
The bootable array must contain your configured  
operating system...  
27  
 
FastTrak TX4000 User Manual  
Creating a Hot Spare Drive for Mirrored Arrays  
For automatic rebuilds of a mirrored array, attach a spare drive to the FastTrak  
TX4000. Drives that are not assigned to an array and are the same size or  
larger than the original will be used for the automatic rebuild. This is performed  
in the background under all supported operating systems, except DOS. At a  
later time, the system can be turned off and the failed drive can be physically  
removed.  
How FastTrak TX4000 Orders Arrays  
During startup, the disk arrays on the FastTrak TX4000 are recognized in this  
order:  
1. The array set to bootable in the FastBuild Setup.  
2. The Array number (i.e. Array 0, Array 1…). This would be involved in  
determining which drive letters will be assigned to each disk array.  
How FastTrak TX4000 Saves Array Information  
All disk array data is saved into the reserved sector on each array member.  
Promise suggests that users record their disk array information for future  
reference.  
Another feature of the FastTrak TX4000 disk array system is to recognize drive  
members even if drives are moved between different FastTrak TX4000 card  
connectors. Since each drive’s array data identifies itself to the array, it is  
possible to move or swap drives without modifying the array setup. This is  
valuable when adding drives, or during a rebuild.  
28  
 
Chapter 3: FastBuild Configuration Utility  
Deleting an Array  
The Delete Array (4) Menu option allows for deletion of disk array assignments.  
This is not the same as deleting data from the drives themselves.  
Important  
If you delete an array by accident, immediately define a  
new array identical to one you deleted. This action normally  
recovers the deleted array.  
Warning  
Deleting an existing disk array could result in its data loss.  
Make sure to record all array information including the array  
type, the disk members, and stripe block size in case you  
wish to undo a deletion.  
FastBuild (tm) Utility 1.xx (c) 2002-2005 Promise Technology, Inc.  
[ Delete Array Menu ]  
Array No  
Array 1  
Array 2  
Array 3  
Array 4  
RAID Mode  
Stripe  
Mirror  
Total Drv  
Capacity(MB)  
16126  
8063  
Status  
Functional  
Functional  
——  
2
2
——  
——  
——  
——  
——  
——  
——  
[ Keys Available ]  
[] Up [] Down [ESC] Exit [Del] Delete  
1. To delete an array, highlight the Array you wish to delete and press the  
Delete key.  
2. The View Array Definition menu will appear (see below) showing which  
drives are assigned to this array.  
29  
 
FastTrak TX4000 User Manual  
FastBuild (tm) Utility 1.xx (c) 2002-2005 Promise Technology, Inc.  
[ Define Array Menu ]  
Array No  
Array 1  
RAID Mode  
Stripe  
Total Drv  
2
Capacity(MB)  
16126  
Status  
Functional  
Stripe Block: 64 KB  
Gigabyte Boundary: OFF  
[ Drive Assignments ]  
Channel: Drive ID  
Drive Model  
Capacity (MB) Assignment  
1 :  
3 :  
1
3
QUANTUMCR8.4A  
QUANTUMCR8.4A  
8063  
8063  
Y
Y
3. Press Ctrl-Y to confirm Yes to the following warning message and continue  
array deletion:  
Are you sure you want to delete this array?  
Press Ctrl-Y to Delete, others to Abort  
4. After deleting the array, create a new array using Auto Setup or the Define  
Array menu from the FastBuild Main Menu.  
30  
 
Chapter 3: FastBuild Configuration Utility  
Rebuilding a Mirrored Array  
The Rebuild Array (5) Menu option can be used to recover from an error in a  
mirrored disk array. You will receive an error message when booting your  
system from the FastTrak BIOS.  
Important  
Drives MUST be replaced if they contain any physical  
errors.  
Follow these steps before using the Rebuild Array menu option:  
1. On boot up, the FastTrak TX4000 Startup BIOS will display an error  
message identifying which drive has failed.  
2. Press Ctrl-F to enter FastBuild Main Menu.  
3. Select submenu Define Array (3).  
4. Select the failed array and identify the Channel and ID of the failed drive.  
5. Power off and physically remove the failed drive.  
6. Replace the drive with an identical model.  
7. Reboot the system and enter the FastBuild Main Menu.  
8. Select the Rebuild Array (5) option. The following screen will appear.  
FastBuild (tm) Utility 1.xx (c) 2002-2005 Promise Technology, Inc.  
[ Rebuild Array Menu ]  
Array No  
Array 1  
Array 2  
Array 3  
Array 4  
RAID Mode Total Drv  
Capacity(MB)  
16126  
8063  
Status  
Functional  
Critical  
——  
Stripe  
Mirror  
——  
2
2
——  
——  
——  
——  
——  
——  
[ Keys Available ]  
[] Up [] Down [ESC] Exit [Enter] Select  
9. Highlight the array whose Status is Critical.  
10. Press Enter. The following screen will then appear (see next page).  
31  
 
FastTrak TX4000 User Manual  
FastBuild (tm) Utility 1.xx (c) 2002-2005 Promise Technology, Inc.  
[ Rebuild Array Menu ]  
Array No  
Array 2  
RAID Mode  
Mirror  
Total Drv  
2
Status  
Critical  
Stripe Block: Not Available  
Gigabyte Boundary: ON  
[ Select Drive for Rebuild ]  
Channel:  
1 :  
Drive ID  
1
Drive Model  
QUANTUMCR8.4A  
Capacity (MB)  
8063  
[ Keys Available ]  
[] Up [] Down [ESC] Exit [Enter] Select  
11. Under Select Drive for Rebuild, highlight the replacement drive.  
12. Press Enter and confirm that the data will be copied on to the selected  
drive. All data on the replacement drive will be written over with mirrored  
information from the array drive. A progress bar will appear as below.  
Please Wait While Duplicating The Image  
10%  
Complete  
13. Once the rebuild process is complete, reboot the system.  
32  
 
Chapter 4: Installing Software Drivers  
Following are driver installation procedures for the Windows operating systems  
that support the FastTrak TX4000 Controller. The FastTrak TX4000 software  
drivers for Windows are included on the driver diskette.  
Drivers and installation instructions for Linux and Novell operating systems are  
Important  
If you wish to include your current bootable ATA drive using the  
Windows NT4.x, 2000, XP, Server 2003, ME or 98 operating  
system on your FastTrak TX4000 Controller card, you MUST  
install the Windows NT4, 2000, XP, Server 2003, ME or 98  
driver software first onto this drive while it is still attached to your  
existing hard drive controller.  
Procedure  
Page Number  
New Windows Server 2003 Installation......................................... 34  
Existing Windows Server 2003 Installation.................................... 35  
Confirming Windows Server 2003 Driver Installation .................... 35  
New Windows XP Installation........................................................ 36  
Existing Windows XP Installation .................................................. 37  
Confirming Windows XP Driver Installation................................... 37  
New Windows 2000 Installation .................................................... 38  
Existing Windows 2000 Installation............................................... 39  
Confirming Windows 2000 Driver Installation................................ 39  
New Windows ME Installation....................................................... 40  
Existing Windows ME Installation.................................................. 41  
Confirming Widows ME Driver Installation .................................... 41  
New Windows NT4.x Installation................................................... 42  
Existing Windows NT4.x Installation ............................................. 43  
Removing Driver from Windows NT4.x ......................................... 43  
New Windows 98 Installation ........................................................ 44  
Existing Windows 98 Installation................................................... 45  
Confirming Windows 98 Driver Installation.................................... 45  
33  
 
FastTrak TX4000 User Manual  
New Windows Server 2003 Installation  
The following details the installation of the FastTrak TX4000 drivers while installing  
Windows Server 2003.  
1. Start the installation:  
Floppy Install: Boot the computer with the Windows Server 2003  
installation diskettes.  
CD-ROM Install: Boot from the CD-ROM. Press F6 after the message  
“Press F6 if you need to install third party SCSI or RAID driver”  
appears.  
2. When the Windows Server 2003 Setup window is generated, press S to  
specify an Additional Device(s).  
3. Insert the FastTrak TX4000 driver diskette into drive A: and press Enter.  
4. Choose Win .NET 2003 Promise FastTrak TX4000/S150 TX Series (tm)  
Controller from the list that appears on screen, and then press the Enter.  
5. Press S to use the driver on the floppy disk and then press Enter to  
continue with installation.  
6. The Windows Server 2003 Setup screen will appear again saying “Setup  
will load support for the following mass storage devices:” The list will include  
“Win .NET 2003 Promise FastTrak TX4000/S150 TX Series (tm) Controller”.  
NOTE: If there are any additional devices to be installed, specify them now.  
When all devices are specified, continue to the next step.  
7. From the Windows Server 2003 Setup screen, press the Enter. Setup will  
now load all device files and then continue the Windows Server 2003  
installation.  
34  
 
Chapter 4: Installing Software Drivers  
Existing Windows Server 2003 Installation  
After installing the FastTrak TX4000 card and rebooting your system, Windows  
Server 2003 setup will show a “Found New Hardware” dialog box.  
1. Insert the FastTrak TX4000 driver diskette into the A:\ drive.  
2. Choose Install the software automatically and press the Enter key.  
3. Choose Win .NET 2003 Promise FastTrak TX4000/S150 TX Series (tm)  
Controller from the list that appears on screen, and then press the Enter  
key.  
4. If using a driver that has not been digitally signed by Microsoft, you will be  
asked if you want to continue the installation. Click Continue anyway.  
5. When the New Hardware Wizard has finished installing the FastTrak  
TX4000 software, click Finish.  
Confirming Windows Server 2003 Driver  
Installation  
1. Right-click on the My Computer icon and select Manage from the popup  
menu.  
2. From the left panel, select Device Manager.  
3. Click the “+” in front of SCSI and RAID controllers. “Win .NET 2003 Promise  
FastTrak TX4000/S150 TX Series (tm) Controller” should appear.  
35  
 
FastTrak TX4000 User Manual  
New Windows XP Installation  
The following details the installation of the FastTrak TX4000 drivers while  
installing Windows XP.  
1. Start the installation:  
Floppy Install: Boot the computer with the Windows XP installation  
diskettes.  
CD-ROM Install: Boot from the CD-ROM. Press F6 after the message  
“Press F6 if you need to install third party SCSI or RAID driver”  
appears.  
2. When the Windows XP Text Setup is generated, press S to specify an  
Additional Device(s).  
3. Insert the FastTrak TX4000 driver diskette into drive A: and press Enter.  
4. Choose WinXP Promise FastTrak TX4000 Controller from the list that  
appears on screen, and then press the Enter.  
5. Press Enter to continue with installation.  
6. The Windows XP Setup screen will appear again saying “Setup will load  
support for the following mass storage devices:” The list will include WinXP  
Promise FastTrak TX4000 Controller.  
NOTE: If there are any additional devices to be installed, specify them now.  
When all devices are specified, continue to the next step.  
7. From the Windows XP Setup screen, press the Enter. Setup will now load  
all device files and then continue the Windows XP installation.  
36  
 
Chapter 4: Installing Software Drivers  
Existing Windows XP Installation  
After installing the FastTrak TX4000 card and rebooting your system, Windows  
XP setup will show a “Found New Hardware” dialog box. Under Windows XP,  
“Mass Storage Controller” will be displayed.  
1. Insert the FastTrak TX4000 driver diskette into the A:\ drive.  
2. Choose Install the software automatically and press the Enter key.  
3. Choose WinXP Promise FastTrak TX4000 Controller from the list that  
appears on screen, and then press the Enter key.  
4. If using a driver that has not been digitally signed by Microsoft, you will be  
asked if you want to continue the installation. Click Continue anyway.  
5. When the New Hardware Wizard has finished installing the FastTrak  
TX4000 software, click Finish.  
6. Reboot your system.  
Confirming Windows XP Driver Installation  
1. From Windows XP, open the Control Panel from the My Computer icon.  
2. Click Performance and maintenance.  
3. Click the System icon.  
4. Click the Hardware tab, then click the Device Manager tab.  
5. Click the “+” in front of SCSI and RAID controllers. WinXP Promise  
FastTrak TX4000 Controller should appear.  
37  
 
FastTrak TX4000 User Manual  
New Windows 2000 Installation  
The following details the installation of the FastTrak TX4000 drivers while  
installing Windows 2000.  
1. Start the installation:  
Floppy Install: Boot the computer with the Windows 2000 installation  
diskettes.  
CD-ROM Install: Boot from the CD-ROM. Press F6 after the message  
“Press F6 if you need to install third party SCSI or RAID driver”  
appears.  
2. When the Windows 2000 Setup window is generated, press S to specify an  
Additional Device(s).  
3. Insert the FastTrak TX4000 driver diskette into drive A: and press Enter.  
4. Choose Win2000 Promise FastTrak TX4000 Controller from the list that  
appears on screen then press Enter.  
5. The Windows 2000 Setup screen will appear again saying “Setup will load  
support for the following mass storage devices:” The list will include  
Win2000 Promise FastTrak TX4000 Controller.  
NOTE: If there are any additional devices to be installed, specify them now.  
When all devices are specified, continue to the next step.  
6. From the Windows 2000 Setup screen, press Enter. Setup will now load all  
device files and then continue the Windows 2000 installation.  
38  
 
Chapter 4: Installing Software Drivers  
Existing Windows 2000  
After installing the FastTrak TX4000 card and rebooting your system, Windows  
2000 setup will show a “New Hardware Found” dialog box. Under Windows  
2000, “PCI Mass Storage Controller” will be displayed.  
1. Choose Add New Hardware Wizard from the list, and then press Enter.  
2. Choose Add/Troubleshoot a device and click Next. The new hardware  
wizard will show device list  
3. Choose Mass Storage controller and click Next. At the following screen click  
Finish.  
4. Choose Display a list the known drivers for this device so that I can choose  
a specific driver then click Next.  
5. When the Windows 2000 supported SCSI adapter drivers list appears, click  
Have disk.  
6. Insert the FastTrak TX4000 driver diskette in drive A:\.  
7. Type A:\Win2000 in the text box. Click OK .  
8. Choose Win2000 Promise FastTrak TX4000 Controller from the list that  
appears on screen, then click Next.  
9. Click Yes to confirm continue the installation and copy the driver to system.  
10. Remove the diskette and click Finish to restart the system. Windows 2000  
will then restart for the driver installation to take effect.  
Confirming Windows 2000 Driver Installation  
1. From Windows 2000, open the Control Panel from My Computer icon  
followed by the System icon.  
2. Choose the Hardware tab, and then click the Device Manager tab.  
3. Click the “+” in front of SCSI and RAID controllers. Win2000 Promise  
FastTrak TX4000 Controller should appear.  
39  
 
FastTrak TX4000 User Manual  
New Windows ME Installation  
The following details the installation of the FastTrak TX4000 drivers while  
installing Windows ME.  
1. Install the FastTrak TX4000 controller card into your system.  
2. Install Windows ME fully.  
3. After installation, go to the Start menu and choose Settings.  
4. From the Settings menu, choose Control Panel.  
5. In the Control Panel window, double-click the System icon.  
6. In the System window, choose the Device Manager tab.  
7. In the hierarchical display under Other Devices is a listing for PCI RAID  
Controller. Click it then click the Properties button.  
8. In the Properties window, choose the Driver tab then choose Update Driver  
and click Next.  
9. Choose Search for a better driver than the one your device is using now  
(recommended) then click Next.  
10. Choose Specify Location then type A:\WIN98-ME in the text box.  
11. Insert the FastTrak TX4000 driver diskette into the A: drive.  
12. Click the Next button. A message informing you that “Win98-ME Promise  
FastTrak TX4000 Controller” should appear.  
13. Click Next, then click Finish.  
14. When asked if you want to restart your computer, click Yes. Immediately  
remove the diskette from drive A:.  
40  
 
Chapter 4: Installing Software Drivers  
Existing Windows ME Installation  
The following section details the installation of FastTrak TX4000 drivers on a  
system that has Windows ME already installed and running.  
1. After installing the FastTrak TX4000 controller card and configuring the hard  
drives, power up the system and boot.  
2. The Add New Hardware Wizard will appear, informing you that it has found  
a PCI Mass Storage Controller.  
3. Click Next, then from the generated list box, choose Specify the location of  
the driver (Advanced).  
4. Click Next, then from the generated choices, choose Specify a location.  
5. Insert the FastTrak TX4000 driver diskette in drive A:.  
6. Type A:\WIN98-ME in the text box that appears.  
7. Click Next. A message informing you that Windows ME has found “Win98-  
ME Promise FastTrak TX4000 Controller” should appear.  
8. Click Next, then click Finish. When asked if you want to restart your  
computer, click Yes. Immediately remove the diskette from drive A:.  
Confirming Driver Installation in Windows ME  
To confirm that the driver has been properly loaded in Me, perform the following  
steps:  
1. Choose Settings from the Start menu.  
2. Choose Control Panel, then double-click the System icon.  
3. Choose the Device Manager tab, then click the “+” in front of SCSI & RAID  
controllers. “Win98-ME Promise FastTrak TX4000 Controller” should  
appear.  
41  
 
FastTrak TX4000 User Manual  
New Windows NT4.x Installation  
The following details the installation of the FastTrak TX4000 drivers while  
installing Windows NT4.x.  
1. Start the system installation by booting from the Windows NT disk:  
Floppy install: boot the system with the Windows NT installation  
diskettes.  
CD-ROM disk install: boot from the CD-ROM disk and press F6 when  
the message “Setup is inspecting your computer’s hardware  
configuration…” appears.  
2. When the Windows NT Setup window is generated, press S to Specify an  
Additional Device(s).  
3. Insert the FastTrak TX4000 driver diskette into drive A: and press Enter.  
4. Choose WinNT Promise FastTrak TX4000 Controller from the list that  
appears on screen then press Enter.  
5. The Windows NT Setup screen will appear again saying “Setup will load  
support for the following mass storage devices:” The list will include WinNT  
Promise FastTrak TX4000 Controller.  
NOTE: If there are any additional devices to be installed, specify them now.  
When all devices are specified, continue to the next step.  
6. From the Windows NT Setup screen, press Enter. Setup will now load all  
device files and then continue the Windows NT installation.  
7. After a successful installation, the SCSI Adapter Setup box will show that  
the WinNT Promise FastTrak TX4000 Controller driver has been installed.  
42  
 
Chapter 4: Installing Software Drivers  
Existing Windows NT4.x Installation  
The following section details the installation of FastTrak TX4000 drivers on a  
system that has Windows NT4.x already installed and running.  
NOTE: Do not attach the boot drive or any other hard drive to the FastTrak  
TX4000 controller card before completing this step.  
1. From the Start menu, choose Settings.  
2. From the Settings menu, choose Control Panel.  
3. Double-click the SCSI Adapters icon. The SCSI Adapters dialog box  
appears.  
4. Choose Drivers then click Add.  
5. In the Install Drivers dialog box, click Have Disk…  
6. When Install From Disk appears, insert the FastTrak TX4000 driver diskette  
in drive A:.  
7. Type A:\NT4 in the text box window then click OK.  
8. When the Install Driver dialog box appears, select WinNT Promise FastTrak  
TX4000 Controller then click OK.  
9. When the Select SCSI Adapter Option dialog box appears, click Install.  
10. After a successful installation, the SCSI Adapter Setup box will show that  
the WinNT Promise FastTrak TX4000 Controller has been installed.  
11. Power off your system.  
12. If you plan to move the boot drive to the FastTrak card, connect the boot  
drive now.  
13. Power on your system.  
Removing the Driver from Windows NT4.x  
1. From Start, choose Setup then choose Control Panel.  
2. In Control Panel, choose SCSI Adapter then choose Drivers.  
3. Select the “Winnt Promise FastTrak TX4000 RAID Controller”.  
4. Click the Remove button.  
43  
 
FastTrak TX4000 User Manual  
New Windows 98 Installation  
The following section details the installation of the FastTrak TX4000 drivers  
while installing Windows 98.  
1. Install the FastTrak TX4000 controller card and configure the hard drive(s),  
partition and format your hard drive(s), if necessary.  
2. Install Windows 98 normally.  
3. After installation, go the Start menu and choose Settings.  
4. From the Settings menu, choose Control Panel.  
5. In the Control Panel window, double-click the System icon.  
6. In the System window, choose the Device Manager tab.  
7. In the hierarchical display under Other Device is a listing for PCI RAID  
Controller. Select it then click the Properties button.  
8. Choose the Driver tab in the Properties window, choose Update Driver then  
click Next.  
9. Choose Search for a better driver than the one your device is using now  
(recommended), then click Next.  
10. Choose Specify Location then type A:\WIN98-ME in the text box.  
11. Insert the FastTrak TX4000 driver diskette into the A: drive.  
12. Click the Next button. A message informing you that “Windows 98 has  
found Win98-ME Promise FastTrak TX4000 RAID Controller” should  
appear.  
13. Click Next, then Finish.  
14. When asked if you want to restart your computer, click Yes. Immediately  
remove the diskette from drive A:.  
44  
 
Chapter 4: Installing Software Drivers  
Existing Windows 98 Installation  
The following section details the installation of FastTrak TX4000 drivers on a  
system that has Windows 98 already installed and running.  
1. After installing the FastTrak TX4000 controller card and configuring the hard  
drives, power up the system and boot Windows.  
2. The “Add New Hardware Wizard” will appear, informing you that it has  
found a “PCI Mass Storage Controller.”  
3. Click Next. From the generated list box, choose Search for best driver for  
your device (Recommended).  
4. Insert the FastTrak TX4000 driver diskette in drive A:.  
5. Click Next. From the generated choices, choose Specify a location.  
6. Type A:\WIN98-ME in the text box that appears.  
7. Click Next. A message informing you that Windows has found “Win98-ME  
Promise FastTrak TX4000 RAID Controller” should appear.  
8. Click Next, then click Finish.  
9. Click Yes when asked if you want to restart your computer. Be sure to eject  
the diskette from drive A:.  
Confirming Driver Installation in Windows 98  
To confirm that the driver has been properly loaded in Windows 98, perform the  
following steps:  
1. Choose Settings from the Start menu.  
2. Choose Control Panel, then double-click the System icon.  
3. Choose the Device Manager tab, then click the “+” in front of SCSI  
controllers. “Win98-ME Promise FastTrak TX4000 Controller” should  
appear.  
45  
 
FastTrak TX4000 User Manual  
46  
 
Chapter 5: Disk Array Concepts  
About FastTrak TX4000  
FastTrak TX4000 is a high performance Ultra ATA RAID controller card that  
features concurrent data channel operation and onboard BIOS. The channels on  
the FastTrak TX4000 support concurrent operation that allows for overlapped  
I/O under multi-tasking operating systems and sharing the workload between  
multiple drives.  
About Adapter BIOS  
The FastTrak TX4000 card contains a BIOS code that extends the standard disk  
service routine provided through Int13. The BIOS is bootable for DOS and other  
operating systems that rely on the system BIOS for drive operation. When the  
FastTrak TX4000 BIOS appears during boot up, press Ctrl-F to enter the  
FastBuild setup to select from menu settings.  
FastBuild Auto Menu Setup  
This setup utility is used to build and manage FastTrak TX4000 disk arrays. The  
utility is menu driven and features the Auto Setup (1) option that uses a simple,  
interactive setup process. Once the array is built, all the array members store  
the configuration information in the drive’s reserved area. See Chapter 3, which  
provides descriptions of individual functions.  
Reserve Sector  
Array configuration data about the drive member and other members in the disk  
array are saved on a special location on the disk drives called the reserve  
sector. If any member of the array becomes corrupt or lost, the redundant  
configuration data on the other members can be used for rebuilds.  
Disk array members do not have a memory of their drive positions. This allows  
drives to be placed on different FastTrak TX4000 connectors or cards within the  
system without reconfiguring or rebuilding.  
47  
 
FastTrak TX4000 User Manual  
Disk Array Terms  
Disk Array Description  
A disk array is formed from a group of two or more disk drives that appear to the  
system as a single drive. The advantage of an array is to provide better  
throughput performance and/or data fault tolerance.  
Better performance is accomplished by sharing the workload among multiple  
physical drives.  
Fault tolerance is achieved through data redundancy operation where if one (or  
more) drive fails or has a sector failure, a mirrored copy of the data can be found  
on another drive(s).  
For optimal results, select identical Ultra ATA/133 drives to install in disk arrays.  
The drives’ matched performance allows the array to function better as a single  
drive.  
Disk Array Member  
The individual disk drives in an array are called members. Each member of a  
specific disk array has coded in its reserved sector configuration information that  
identifies the drive as a member. All disk members in a formed disk array are  
recognized as a single physical drive to the system.  
Disk Array Types  
For most installations, the FastBuild setup Auto Setup (1) option will configure  
your system.  
There are three disk array types in two categories that can be installed on the  
FastTrak TX4000 card. Striping is in the Performance category while Mirroring,  
Striping/Mirroring are in the Fault Tolerance category.  
Disk arrays within the Performance and Fault Tolerance categories conform to  
the Redundant Array of Independent Disks technology, or RAID. The RAID  
levels supported are 0, 1, and 0+1.  
Fault  
Tolerance  
No. of  
Drives  
RAID Level  
Performance  
Highest  
Normal  
Capacity  
RAID 0  
(Striping)  
No. Drives x  
Smallest Size  
No  
2 to 4  
RAID 1  
(Mirroring)  
Yes  
Yes  
Smallest Size Drive  
2
4
RAID 0+1  
(Stripe/Mirror)  
2X Smallest Size  
Drive  
High  
48  
 
Chapter 5: Disk Array Concepts  
About RAID Levels  
Striping (RAID 0)  
Reads and writes sectors of data interleaved between multiple drives. When any  
disk member fails, it affects the entire array. Performance is better than a single  
drive since the workload is balanced between the array members.  
This array type is for high performance systems. Identical drives are  
recommended for performance as well as data storage efficiency. The disk array  
data capacity is equal to the number of drive members times the smallest  
member capacity. For example, one 100 GB and three 120 GB drives will form a  
400 GB (4 x 100 GB) disk array.  
Stripe Size – A value can be set from 16KB to 256KB sector size. The size can  
directly affect performance. In the FastBuild BIOS, the default is 64KB.  
Data  
Stripe  
1
3
5
7
2
4
6
8
Disk Drives  
49  
 
FastTrak TX4000 User Manual  
Mirroring (RAID 1)  
Writes duplicate data on to a pair of drives while reads are performed in parallel.  
ATA RAID 1 is fault tolerant because each drive of a mirrored pair is installed on  
separate IDE channels. If one of the mirrored drives suffers a mechanical failure  
(for example, spindle failure) or does not respond, the remaining drive will  
continue to function. This is called Fault Tolerance. If one drive has a physical  
sector error, the mirrored drive will continue to function.  
Data Mirror  
1
2
3
4
1
2
3
4
Disk Drives  
On the next reboot, the FastBuild™ Utility will display an error in the array and  
recommend replacing the failed drive. Users may choose to continue using their  
PC, however Promise recommends replacing the failed drive as soon as  
possible.  
Due to redundancy, the drive capacity of the array is half the total drive capacity.  
For example, two 100 GB drives that have a combined capacity of 200 GB  
would have 100 GB of usable storage. With drives of different capacities, there  
may be unused capacity on the larger drive.  
Using a Spare Drive – Under a RAID 1, you can attach a third drive to the  
FastTrak TX4000 as a hot spare without assigning it to the array. Such a drive  
will be activated to replace a failed drive in the array. A rebuild takes place  
automatically in the background to mirror the good drive data onto the spare.  
At a later time, the system can be powered off and the failed drive can be  
physically removed and replaced. Spare drives must be the same or larger  
capacity than the smallest array member.  
50  
 
Chapter 5: Disk Array Concepts  
Striping / Mirror (RAID 0+1)  
A combination of RAID 0 and RAID 1 arrays. It can increase performance by  
reading and writing data in parallel while protecting data with duplication. A  
minimum of four drives are required.  
With a four-drive disk array, two pairs of drives are striped. Each pair mirrors the  
data on the other pair of striped drives. The data capacity is similar to a standard  
Mirroring array with half of total capacity dedicated for redundancy.  
Data Stripe  
2
4
6
8
1
3
5
7
Data  
Mirror  
2
4
6
8
1
3
5
7
Disk Drives  
51  
 
FastTrak TX4000 User Manual  
About Dual Data Redundancy  
One unique (though rarely occurring) feature of RAID 0+1 is dual fault tolerance.  
In some cases, two drives can fail simultaneously and still maintain the integrity  
of data. There are six combinations in which two drives can fail. FastTrak  
TX4000 protects the data array in four of those cases depending on drive type  
(some drives do not permit the Slave drive to continue to function if the Master  
drive fails).  
Assume the drives are configured as follows:  
IDE indicates channels on the FastTrak TX4000 card.  
A/B indicates which striped pair the drive belongs to.  
1/2 indicates which part of stripe data.  
IDE 1  
IDE2  
IDE3  
IDE4  
Drive A1  
Drive B1  
Drive A2  
Drive B2  
Note that FastTrak TX4000 card does not use Master/Slave drive settings.  
Under RAID 0+1, the array maintains data integrity if any A, B combination  
survives.  
Failed  
Drives  
Array  
Status  
Event  
Why?  
1
2
3
4
5
6
A1/A2  
B1/B2  
A1/B2  
B1/A2  
A1/B1  
B2/A2  
Offline  
B1/B2 contain only half of array data  
A1/A2 contain only half of array data  
B1/A2 retain array integrity  
A1/B2 retain array integrity  
B2/A2 retain array integrity  
A1/B1 retain array integrity  
Offline  
Functional  
Functional  
Functional  
Functional  
52  
 
Chapter 6: Troubleshooting & Tips  
This section is used to assist with troubleshooting conflicts and FastTrak  
TX4000 installation problems. Also refer to the README.TXT file on the  
FastTrak TX4000 driver and utility diskette for more recent information as well as  
the PromiseOnline services listed in Appendix A.  
The section is divided into the following categories: Motherboard Issues, System  
CMOS Issues, Drive Errors, Operating System Errors, and Audio/Video Editing  
Tips.  
Motherboard Issues  
Freeing additional IRQ resources  
Since the Promise card supports PCI Interrupt sharing, it is possible to use IRQs  
already assigned to another PCI card. Interrupt Sharing is not supported with  
onboard IDE controllers. If the onboard IDE controller(s) are not used, you may  
disable the controllers to free IRQ 14 and/or 15.  
Configuring PCI IRQ resources  
Setting the IRQ for a particular PCI slot will be different depending on the  
motherboard BIOS. This setting is usually made in the PCI Configuration and/or  
Plug and Play (PnP) section of the motherboard BIOS setup. There are three  
common methods that motherboard BIOS’s handle assignment of IRQs to PCI  
slots:  
Specifically assigning an IRQ to a particular slot - You can tell the  
motherboard to use IRQ 10 for PCI slot 1, IRQ 11 for PCI slot 2, etc.  
Listing which IRQs are available to be assigned to the PCI slots - This BIOS  
has an option where you specify 1st Available IRQ, 2nd Available IRQ, etc.  
The BIOS then scans the PCI slots for PCI cards and assigns these IRQs in  
the order that it finds the PCI cards.  
Excluding an IRQ from being used by a PCI slot – If you have an ISA card  
that is using an IRQ, change the setting for this particular IRQ from  
Available to Used by ISA card so that the motherboard will not assign this  
IRQ to a PCI slot.  
Consult your motherboard manual for information that is specific to your  
motherboard.  
System locks up during boot up or when Windows starts  
There may be a possible IRQ conflict with an ISA card. Identify what IRQs are  
used by ISA cards, enter the Motherboard PCI Setup, and reserve the IRQ for  
use with ISA. PCI slots cannot share IRQs with ISA cards.  
53  
 
FastTrak TX4000 User Manual  
Miscellaneous problems such as:  
FastTrak TX4000 BIOS does not appear during boot  
FastTrak TX4000 driver does not load  
Slow data transfer rates  
Move the FastTrak TX4000 card to a different PCI slot.  
Intermittent data problems  
Overclocking the PCI bus may cause the system to hang or data corruption. If  
you experience either of these problems and you are overclocking the PCI bus,  
set the PCI bus back to its normal setting to see if this is causing the errors.  
System CMOS Issues  
Set Motherboard CMOS Boot sequence to boot to FastTrak TX4000  
On some Motherboard BIOS, it is necessary to set the Boot sequence to SCSI,  
A:, C: since the Promise card is identified as a SCSI card.  
Motherboard CMOS displays C: or D: drive failure during startup  
See the Drive-Related Errors section.  
Using an Onboard IDE Card with FastTrak TX4000  
If an onboard IDE controller is installed with hard disks, enable support in the  
Motherboard Standard CMOS Setup for the drives. Note that the onboard IDE  
hard drives will then be the bootable hard disk unless the system BIOS has a  
boot sequence setting with the option to specify booting to a different device.  
54  
 
Chapter 6: Troubleshooting & Tips  
Drive-Related Errors  
Critical Array Status Error Reported during Boot  
If a critical status error message appears on the FastTrak TX4000 BIOS startup  
screen for a mirrored array (see below), there is a drive in the array that has  
failed or is not responding. FastTrak TX4000 will identify the failed drive by  
channel number. The mirrored array has lost its fault tolerance, but will still  
perform normal drive reads and writes.  
Operation aborted because FastBuild encountered an error as  
follows:  
Location: Channel 2  
Array Status: Critical  
Please retry using Promise Array Management utility to recover all  
data. Reboot the system by pressing the ENTER key.  
Try powering the system off and on to reset the drive. Also confirm that cables  
are properly attached and the drive is receiving power. If the drive still appears  
to have failed, refer to the Rebuilding an Array option in the Promise Array  
Management (PAM) utility as detailed in the PAM User Manual.  
Drive cannot be formed into an array  
Drives must support Ultra DMA or Multi-word DMA and be free of media defects  
to be added into an array. Promise recommends using new identical drives for  
each array. Re-secure data and power cabling while checking for proper  
alignment. Typically, Pin 1 of the drive is closest to the power connector.  
System CMOS displays C: or D: drive failure during Startup  
Do not reference C: or D: in the Motherboard Standard CMOS for drives  
attached to the FastTrak TX4000 controller. Only enter drive information in the  
Motherboard CMOS for drives attached to the onboard IDE controller.  
FDISK reports a much lower drive capacity if a single physical drive or a  
striped array exceeds 64GB  
Due to a limitation with FDISK, the utility reports only the storage capacity that  
exceeds 64GB. This is a cosmetic, not actual, limitation. Simply create a single  
DOS drive partition, reboot, and then format the partition. The Format command  
will recognize the total capacity of the partition accurately. Windows NT/2000/98  
will now recognize the total capacity of your array.  
55  
 
FastTrak TX4000 User Manual  
Unable to partition or format array  
There are two possible causes:  
The FastTrak TX4000 controller is the bootable device but the array is not  
set to be bootable.  
The Reserve Sector of one of the drives has become corrupt or bad.  
If the FastTrak TX4000 controller is the bootable device, make sure that the  
array is set to be bootable:  
1. During boot up, press Ctrl-F to enter the FastBuild BIOS utility  
2. Choose option 3, Define Array.  
3. Press the Up Down keys to highlight the array that you want to boot  
from.  
4. Press the Spacebar to select.  
An * asterisk will appear next to the array number indicating it as bootable. The  
system will now recognize this array as the first array seen. The system will then  
use this bootable array as the (fixed) boot C: drive.  
The Reserve Sector of one of the drives has become corrupt or bad. Removing  
the Reserve Sector will remedy any issue related directly to a Bad Reserve  
Sector.  
Warning  
Before removing the Reserve Sector of the drive(s), backup  
any existing data. Removal of the reserve sector of any  
drive permanently deletes all existing data on the hard  
drive.  
For Mirrored arrays (RAID 1), remove the Reserve Sector from the mirrored  
drive first (this will appear during Step 3 below) then rebuild the mirrored array.  
Remove the Sector on the Master Drive only as a last resort.  
For Striped arrays (RAID 0), removing the Reserve Sector from any of the drives  
that are striped will destroy the arrayed data.  
56  
 
Chapter 6: Troubleshooting & Tips  
To remove the Reserve Sector, follow these steps:  
1. During boot up, press Ctrl-F to enter the FastBuild BIOS utility.  
2. Choose option 2, View Drive Assignments.  
3. Press arrow keys to highlight the drive where you wish to remove the  
reserve sector.  
4. Press Alt-F1. The highlighted drive will start blinking on the screen.  
5. Press Ctrl-Tab. A message will appear that says the reserved sector (which  
is where array information is kept) on the disk will be wiped.  
6. Press Y to confirm.  
7. Take the appropriate action:  
For striped arrays, repeat this process for each member of the  
particular array that is having a problem. When you are finished, press  
the Esc key twice to reboot.  
For mirrored arrays, hit the Esc key twice to reboot.  
8. After rebooting, use FastBuild to re-create the array.  
For striped arrays, use FDISK and FORMAT after setting up the array.  
For mirrored arrays, rebuild the mirrored array.  
Array Constantly Goes Into Critical or Offline Mode During Reboot  
(see Unable to Partition or Format array above)  
Cannot Rebuild Mirrored (RAID 1) Array  
(see Unable to Partition or Format array above)  
Fatal Errors or Data Corruption Are Constantly Reported When Reading or  
Writing to Drive Array  
(see Unable to Partition or Format array above)  
57  
 
FastTrak TX4000 User Manual  
Operating System-Related Issues  
Different drive lettering under Windows NT  
This may happen when using a SCSI card in addition to the Promise card.  
Windows NT does not necessarily load the driver for the boot device controller  
first. This results in a drive that in MS-DOS is the C: drive being the D:, or E:,  
etc. in Windows NT. Use the Windows NT Disk Administrator utility to reassign  
the letters that NT has improperly assigned to the drives. See your Windows NT  
documentation for instructions on how to use Disk Administrator.  
The Operating System no longer boots after creating a Mirrored Array  
using your existing boot drive using Windows  
This is due to Drive Geometry issues. You can verify this if you move the original  
drive back to the onboard controller and it boots successfully. Each controller  
can view a drive differently. This can be an issue for a new controller that loads  
the original Master Boot Record (MBR) and then has a problem translating it or  
the Operating System boot record.  
For Windows NT, 2000, XP and Server 2003, Promise recommends a clean  
install of the Operating System. This action restores the MBR and OS boot  
record. This requires repartitioning and formatting the drive.  
For Windows 98 and ME, you can perform the DOS Command SYS C: from a  
bootable floppy or CD-ROM to restore the operating system boot record and  
transfer the system files to the boot drive. If this does not work, the Windows  
registry may have become corrupted during the boot process and must be  
restored. See the Windows documentation to perform this procedure.  
Promise Windows driver does not appear in Device Manager  
Windows may already be listing the controller under Other Devices instead of  
the Hard disk controllers section. In Device Manager under Other Devices to see  
if it lists a PCI Card or RAID Controller. If so, highlight this listing and click on the  
Properties button then click on the Driver tab. Depending on your version of  
Windows, choose either Change Driver or Update Driver. Follow the on-screen  
prompts to complete installation of the driver. If Windows asks if you want to test  
if the device can be removed safely, click on CANCEL. Reboot the system to  
complete installation of the driver.  
“Inaccessible Boot Device” Message Appears During Floppyless Install of  
Windows NT, 2000, XP or Server 2003  
The F6 key was not pressed at the appropriate time. Reboot the system, and  
press the F6 key when the message “Setup is inspecting your computer’s  
hardware configuration…” appears in Windows NT4 or the message “Press F6 if  
you need to install third party SCSI or RAID driver” appears in Windows 2000,  
XP and Server 2003.  
58  
 
Chapter 6: Troubleshooting & Tips  
“No Hard Drives Found” Message Appears During CD-ROM Install of  
Windows NT, 2000, XP or Server 2003  
The F6 key was not pressed at the appropriate time. Reboot the system, and  
press the F6 key when the message “Setup is inspecting your computer’s  
hardware configuration…” appears in Windows NT4 or the message “Press F6 if  
you need to install third party SCSI or RAID driver” appears in Windows 2000,  
XP and Server 2003.  
59  
 
FastTrak TX4000 User Manual  
Performance Tips  
Here are some tips that may optimize performance in a RAID 0 striped array. If  
you are using an audio/video-editing card, we also recommend reviewing your  
card’s documentation for additional information.  
Use FastTrak TX4000 as D: or other non-bootable drive in a Striped Array  
For Audio/Video editing, keep the original system boot drive on the standard IDE  
controller as C: drive. Partitioning software such as FDISK will see the array as  
one physical drive, D: or later. This will prevent file fragmentation and provide  
better accessibility to the array.  
Re-Configure PCI Latency Setting  
The PCI Latency setting appears in some Motherboard BIOS. The setting  
governs how much time is allocated to service each PCI slot. Promise  
recommends a value of 64. An optimal value will vary from system to system.  
Optimize Array for “Performance”  
The Promise FastBuild BIOS Utility autosetup menu allows optimizing the array  
for A/V Editing. The default Performance setting (Striping) selects a Stripe Block  
size of 64. This larger block size is recommended for the data streaming  
requirements of A/V editing. You may select an even larger block size in manual  
mode (see Chapter 3).  
FastTrak (tm) / FastTrak TX4000 (tm) BIOS Version 1.xx (Build xxxx)  
(c) 2002-2005 Promise Technology, Inc. All Rights Reserved.  
[ Auto Setup Options Menu ]  
Optimize Array for:  
Typical Application usage:  
Performance  
A/V Editing  
[ Auto Setup Configuration ]  
Mode.................................................... Stripe  
Stripe Block Size........................................64  
Drive used in Array ......................................2  
Array Disk Capacity .............................13044  
[ Keys Available ]  
[] Up [] Down [, , Space] Change Option [ESC] Exit [Ctrl-Y] Save  
60  
 
Chapter 6: Troubleshooting & Tips  
Change Setting of PCI Bus Utilization  
Certain brands of video capture cards can produce a glitch on play back of .AVI  
files. A setting of Less for PCI Bus utilization reduces the time which FastTrak  
TX4000 occupies on the PCI bus and frees that time for use by other PCI  
devices and will eliminate the glitch dropout effect on playback.  
1. In PAM, click on the Controller icon  
Information View.  
in Tree View to display its Options in  
2. At the bottom of the window is the PCI bus utilization slider.  
3. Move the slider to the left for Less, then click the Commit button.  
Once a PCI bus setting has been selected, no reboot is required.  
61  
 
FastTrak TX4000 User Manual  
62  
 
Appendix A: Frequently Asked Questions  
This section lists frequently asked questions involving pre-installation, drive  
issues, installation, and post-installation.  
Pre-Installation  
(Speed, Device Types, Capacity, Cabling)  
Q: What kind of hard drives can I use for a FastTrak TX4000 array?  
A: You can use any IDE hard drive(s) to create arrays on the FastTrak  
TX4000. You should use matching drives for multiple-drive arrays to maximize  
capacity usage as well as performance. Ultra ATA/133 drives are recommended  
for highest performance.  
Q: Will ACPI work with HDDs on the FastTrak TX4000?  
A: Yes.  
Q: Can I use ATAPI devices on the FastTrak TX4000 controller?  
A: No. The FastTrak TX4000 controller does not support ATAPI devices.  
Q: Will the FastTrak TX4000 work with 66MHz PCI bus speed?  
A: Yes, the FastTrak TX4000 is designed to accommodate the newer PCI bus  
speed and is backward compatible with 33MHz speeds.  
Q: How can I change the resources that the FastTrak TX4000 uses?  
A: The FastTrak TX4000 is fully PnP. This means all the resources that it uses  
are given to it by the PnP BIOS on the motherboard. The FastTrak TX4000 does  
support IRQ sharing, but this will not work unless ALL the concerned devices  
support the feature. If your motherboard allows you to control the assignment of  
these resources, you may be able to remedy the problem by:  
Changing the IRQ assignments to the PCI slots in the motherboard BIOS during  
boot up.  
Reset the configuration data in your CMOS. This is usually an option in the PnP  
section of your CMOS.  
Otherwise, switch the FastTrak TX4000 card to a different PCI slot.  
63  
 
FastTrak TX4000 User Manual  
Q: How does the FastTrak TX4000 RAID controller provide storage and/or  
data protection with their arrays?  
A: FastTrak TX4000 implements three different RAID levels as follows:  
RAID 0 (Stripe)  
For capacity – The FastTrak TX4000 array will be as big as the smallest HDD in  
the array times however many HDDs are in the array. Any larger HDDs will  
simply be truncated. The truncated space on the bigger HDDs will then be  
unusable.  
For sustained data transfers – Using FastTrak TX4000, a RAID 0 array  
consisting of two HDDs will transfer at about twice the speed of the slowest HDD  
in the array. A RAID 0 array consisting of four HDDs will transfer at about three  
times the speed of the slowest HDD in the array.  
RAID 1 (Mirror)  
For fault tolerance – The FastTrak TX4000 array will be one-half as big as the  
smaller HDD in the array. The larger HDD will simply be truncated. The  
truncated space on the bigger HDD will then be unusable.  
For sustained data transfers – The FastTrak TX4000 array will write data at the  
rate of the slowest HDD in the array. The FastTrak TX4000 array will read data  
at twice the rate of the slowest HDD in the array.  
RAID 0+1 (Mirror)  
For capacity and fault tolerance – The FastTrak TX4000 array will be equal to  
one-half the number of drives times the capacity of the smallest HDD in the  
array. Larger HDDs will be truncated and that space will be unusable.  
For sustained data transfers – The FastTrak TX4000 array will read and write  
data at twice the rate of the slowest HDD in the array.  
Drive Issues  
Q: Can I add a drive to a FastTrak TX4000 RAID array via hot-swap and  
dynamically adjust the array size/configuration?  
A: No. The FastTrak TX4000 system does not support dynamically adjustable  
RAID size/configurations.  
Q: Do the HDDs on the FastTrak TX4000 have to be the same size?  
A: The HDDs that you use with the FastTrak TX4000 do not have to be the  
same size. If the sizes differ, the FastTrak TX4000 will truncate the bigger HDD  
so the drives match. The resulting difference in HDD space is unusable, so  
avoid using HDDs of significantly different capacities.  
Q: I already have an array on an older FastTrak controller. Can I move  
that array to my new FastTrak TX4000 controller?  
64  
 
Appendix A: FAQs  
A: Yes. All FastTrak controllers read the arrays the same way and can be  
moved from one controller to another.  
Q: Can I take a drive used in a FastTrak TX4000 array and access it  
directly with a different controller, such as the one integrated on the  
motherboard?  
A: Yes, but only under certain configurations. First, the controller must address  
the drives as LBA, not CHS.  
Second, only the following array configurations will allow the drive(s) to be  
accessed individually on another controller:  
Single drive striped (RAID 0)  
Mirrored (RAID 1)  
Multiple drives striped or spanned will not work.  
Q: If I have a problem with one of the drives on the FastTrak TX4000, how  
can I low-level format it to correct the problem?  
A: Do NOT do this. Low-level formatting IDE drives is unnecessary and  
generally does not correct problems commonly experienced during use.  
Errors such as bad sectors or ECC/CRC failure are best remedied by completely  
replacing the drive. For this reason, do NOT low-level format the drives attached  
to the FastTrak TX4000 controller.  
Q: Do I have to install disk management software on my array in order to  
access the full storage capacity of drives?  
A: No! Disk management software will only complicate things. The array  
should be fully addressable by your OS as it is. Remember that some operating  
systems have varying limits on the sizes of partitions and logical drives that can  
be defined. Consult your OS documentation about partitioning larger drives.  
Q: What system BIOS setup settings do I use for the drives on the  
FastTrak TX4000 controller?  
A: None. The drives on the FastTrak TX4000 controller are supported by the  
FastTrak TX4000 BIOS and/or OS drivers, not by your system BIOS.  
Q: How do I partition/format my FastTrak TX4000 RAID array?  
A: The FastTrak TX4000 represents the array as a single HDD to your system.  
Therefore, anything that you can do to a single HDD you can do to a FastTrak  
TX4000 array. For example, you should use the FDISK and FORMAT utilities to  
partition/format the array. You can partition the array as you see fit. You can  
format the array with any file system you wish.  
65  
 
FastTrak TX4000 User Manual  
Installation Issues  
(Capacity, Booting)  
Q: Why are some drives recognized by the FastTrak TX4000 Array Setup  
utilities with only partial capacity?  
A: Some hard drives ship with a jumper that reduces the addressable capacity  
of the drive to prevent problems with older systems that don’t support larger  
drives. Consult your hard drive documentation to set the jumper so that you can  
use the full capacity of the drive.  
Q: How can I change the system boot sequence in order to boot from the  
FastTrak TX4000 array?  
A: The boot sequence is controlled by the system BIOS. As far as the system  
BIOS is concerned, the FastTrak TX4000 controller and defined arrays are  
categorized as a SCSI device. This allows you to set the boot sequence in your  
BIOS setup utility to boot from SCSI first, rather than IDE.  
If there are multiple SCSI add-in controllers in the system, then the boot  
sequence among them will be determined exclusively by their PCI slot priority.  
PCI slot #1 will be first, slot #2 second, etc. Put the FastTrak TX4000 controller  
in the PCI slot where it will be accessed ahead of other SCSI controllers if you  
want to boot from the array.  
Q: How can I change the boot sequence between a PCI SCSI card and the  
FastTrak TX4000 RAID array?  
A: Since all PCI devices are PnP, it is difficult to determine which device is  
addressed first. Some newer motherboard BIOSes have advanced options that  
identify devices and allow you to select which device will be assigned resources  
first. Otherwise you may have to physically switch the device cards on the PCI  
slots so that the boot device is in the highest priority slot number (see previous  
question).  
Post-Installation  
Q: Why can’t I see the drives on the FastTrak TX4000 under FDISK?  
A: You have not created an array yet. If no array has been created, the system  
will not recognize drive(s) attached to the FastTrak TX4000.  
66  
 
Appendix B: Technical Support  
Promise Technical Support provides several support options for Promise users  
to access information and updates. We encourage you to use one of our  
electronic services, which provide product information updates for the most  
efficient service and support.  
If you decide to contact us, please have the following information available:  
Product model and serial number  
BIOS and driver version numbers  
A description of the problem / situation  
System configuration information, including: motherboard and CPU type,  
hard drive model(s), IDE/ATAPI drives & devices, and other controllers.  
Technical Support Services  
Promise OnlineTM Web Site  
(tech documents, drivers, utilities, etc.)  
USA Tech Support Center  
E-mail Support  
Fax Technical Support  
(408) 228-6401  
Attention: Technical Support  
Phone Technical Support  
(408) 228-6402  
7:30-5:00pm M-F Pacific Standard Time  
If you wish to write us for  
support:  
Promise Technology, Inc.  
Attn: Technical Support  
1745 McCandless Drive  
Milpitas, CA 95035, USA  
67  
 
FastTrak TX4000 User Manual  
European Tech Support  
E-mail Support  
Fax Technical Support  
+31 (0)40-256-9463  
Attention: Technical Support  
Phone Technical Support  
+31 (0)40-235-2600  
8:30-5:00pm The Netherlands Time  
If you wish to write us for  
support:  
Promise Technology Europe B.V.  
Attn: Technical Support  
Luchthavenweg 81-125  
5657 EA Eindhoven, The Netherlands  
Pacific Rim Sales Office  
E-mail Support  
Fax Technical Support  
+886-3-578-2390  
Attention: Technical Support  
Phone Technical Support  
+886-3-578-2395 (Ext. 8870)  
9:00-6:00pm Taiwan Time  
If you wish to write us for  
support:  
Promise Technology, Inc.  
Attn: Technical Support  
2F, No. 30, Industry E. Rd. IX  
Science-based Industrial Park  
Hsinchu, Taiwan, R.O.C.  
China Office  
E-mail Support  
Fax Technical Support  
+86 (0) 10-687-23940  
Attention: Technical Support  
Phone Technical Support  
+86 (0) 10-687-23941  
9:00-6:00pm China Time  
If you wish to write us for  
support:  
Promise Technology China  
Attn: Technical Support  
Room 3217, No. 11  
South Zhong Guan Cun Street  
Hai Dian District Beijing 100081  
P.R. China  
68  
 
Appendix B: Technical Support  
Limited Warranty  
Promise Technology, Inc. (“Promise”) warrants that for Three (3) years from the  
time of the delivery of the product to the original end user:  
a)  
b)  
the product will conform to Promise’s specifications;  
the product will be free from defects in material and workmanship  
under normal use and service.  
This warranty:  
a)  
applies only to products which are new and in cartons on the date of  
purchase;  
b)  
c)  
is not transferable;  
is valid only when accompanied by a copy of the original purchase  
invoice.  
d)  
is not valid on spare parts, fans, and power supplies.  
This warranty shall not apply to defects resulting from:  
a)  
improper or inadequate maintenance, or unauthorized modification(s),  
performed by the end user;  
b)  
c)  
operation outside the environmental specifications for the product;  
accident, misuse, negligence, misapplication, abuse, natural or  
personal disaster, or maintenance by anyone other than a Promise or  
a Promise-authorized service center.  
Disclaimer of other warranties  
This warranty covers only parts and labor, and excludes coverage on software  
items as expressly set above.  
Except as expressly set forth above, Promise disclaims any warranties,  
expressed or implied, by statute or otherwise, regarding the product, including,  
without limitation, any warranties for fitness for any purpose, quality,  
merchantability, non-infringement, or otherwise. Promise makes no warranty or  
representation concerning the suitability of any product for use with any other  
item. You assume full responsibility for selecting products and for ensuring that  
the products selected are compatible and appropriate for use with other goods  
with which they will be used.  
Promise does not warrant that any product is free from errors or that it will  
interface without problems with your computer system. It is your responsibility to  
back up or otherwise save important data before installing any product and  
continue to back up your important data regularly.  
69  
 
FastTrak TX4000 User Manual  
No other document, statement or representation may be relied on to vary the  
terms of this limited warranty.  
Promise’s sole responsibility with respect to any product is to do one of the  
following:  
a)  
replace the product with a conforming unit of the same or superior  
product;  
b)  
repair the product;  
Promise shall not be liable for the cost of procuring substitute goods, services,  
lost profits, unrealized savings, equipment damage, costs of recovering,  
reprogramming, or reproducing of programs or data stored in or used with the  
products, or for any other general, special, consequential, indirect, incidental, or  
punitive damages, whether in contract, tort, or otherwise, notwithstanding the  
failure of the essential purpose of the foregoing remedy and regardless of  
whether Promise has been advised of the possibility of such damages. Promise  
is not an insurer. If you desire insurance against such damage, you must obtain  
insurance from another party.  
Some states do not allow the exclusion or limitation of incidental or  
consequential damages for consumer products, so the above limitation may not  
apply to you.  
This warranty gives specific legal rights, and you may also have other rights that  
vary from state to state. This limited warranty is governed by the State of  
California.  
Your Responsibility  
You are responsible for determining whether the product is appropriate for your  
use and will interface with your equipment without malfunction or damage. You  
are also responsible for backing up your data before installing any product and  
for regularly backing up your data after installing the product. Promise is not  
liable for any damage to equipment or data loss resulting from the use of any  
product.  
70  
 
Appendix B: Technical Support  
Returning Product for Repair  
If you suspect a product is not working properly, or if you have any questions  
about your product, contact our Technical Support Staff through one of our  
Technical Services, making sure to provide the following information:  
Product model and serial number (required);  
Return shipping address;  
Daytime phone number;  
Description of the problem;  
Copy of the original purchase invoice.  
The technician will assist you in determining whether the product requires repair.  
If the product needs repair, the Technical Support Department will issue an RMA  
(Return Merchandise Authorization) number.  
Return only the specific product covered by the warranty (do not ship cables,  
manuals, diskettes, etc.), with a copy of your proof of purchase to:  
USA and Canada:  
Promise Technology, Inc.  
Customer Service Dept.  
Attn.: RMA # ______  
1745 McCandless Drive  
Milpitas, CA 95035  
Other Countries:  
Return the product to your dealer or retailer.  
Contact them for instructions before shipping  
the product.  
You must follow the packaging guidelines for returning products:  
Use the original shipping carton and packaging or similar packaging if the  
original is not available  
Include a summary of the product’s problem(s)  
Write an attention line on the box with the RMA number  
Include a copy of proof of purchase  
You are responsible for the cost of insurance and shipment of the product to  
Promise. Note that damage incurred due to improper transport or packaging is  
not covered under the Limited Warranty.  
When repairing returned product(s), Promise may replace defective parts with  
new or reconditioned parts, or replace the entire unit with a new or reconditioned  
unit. In the event of a replacement, the replacement unit will be under warranty  
for the remainder of the original warranty term from purchase date, or 30 days,  
whichever is longer.  
Promise will pay for standard return shipping charges only. You will be required  
to pay for any additional shipping options (such as express shipping).  
71  
 
FastTrak TX4000 User Manual  
72  
 

Philips CD Player CDR775 777 User Manual
Philips Flat Panel Television FTR 9965 12 User Manual
Philips Power Supply SJB4162 User Manual
Philips Projector LC5141 User Manual
Philips Stereo System FW C50 User Manual
Planet Technology Network Router PL 420 User Manual
Playskool Doll 68625 User Manual
Plinius Audio MP3 Player TIKI Network Audio Player User Manual
Poulan Tiller DRT875 User Manual
Powermate Portable Generator PM0435000 User Manual