3-862-222-11 (1)
Compact Disc
Player
Operating Instructions
f
CDP-CX53
1998 by Sony Corporation
TABLE OF CONTENTS
Getting Started
Unpacking ....................................................................................................................... 4
Hooking Up the System ................................................................................................ 4
Inserting CDs.................................................................................................................. 6
Playing a CD ....................................................................................................................... 8
Playing CDs
Locating a Specific Disc .............................................................................................. 10
Specifying the Next Disc to Play ............................................................................... 10
Locating a Specific Track or a Point in a Track ....................................................... 10
Playing Repeatedly ...................................................................................................... 11
Playing in Random Order (Shuffle Play) ................................................................. 12
Creating Your Own Program (Program Play) ......................................................... 13
Playing Your Favorite Disc Independently (Plus One Play) ................................. 15
Playing Discs in a Group (Block Play) ...................................................................... 16
Additional Information
Precautions ................................................................................................................... 17
Notes on CDs................................................................................................................ 17
Troubleshooting ........................................................................................................... 18
Specifications ................................................................................................................ 18
Index ..................................................................................................................................... 19
3
Getting Started
Unpacking
Hooking Up the System
Check that you received the following items:
• Audio cord (1)
• CONTROL A1 cord (1) (supplied for Canadian
models only)
• Remote commander (remote) (1)
• Sony SUM-3 (NS) batteries (2)
• CD booklet holder (1) and label (1)
Overview
This section describes how to hook up the CD player to
an amplifier. Be sure to turn off the power of each
component before making the connections.
S-LINK/CONTROL A1
COMMAND MODE
CD player
How to use the CD booklet holder
The CD booklet holder helps you locate the disc easily.
After you have inserted discs into the player, you can put
the CD booklet (which comes with a CD) into the
supplied holder. Stick the number label on each pocket,
matching the number of the disc slot where you have
inserted the disc. You can put up to 50 CD booklets into
the holder.
To an AC outlet
DIGITAL OUT
To line output (L)
To line output (R)
Inserting batteries into the remote
You can control the player using the supplied remote.
Insert two R6 (size AA) batteries by matching the +
and – on the batteries. When using the remote, point it
at the remote sensor gon the player.
To audio input
Amplifier
: Signal flow
To an AC outlet
When to replace batteries
What cords will I need?
With normal use, the batteries should last for about six
months. When the remote no longer operates the player,
replace all the batteries with new ones.
Audio cord (1) (supplied)
White
(L)
White
(L)
Red
(R)
Red
(R)
Notes
• Do not leave the remote near an extremely hot or humid
place.
• Do not drop any foreign object into the remote casing,
particularly when replacing the batteries.
• Do not expose the remote sensor to direct sunlight or
lighting apparatuses. Doing so may cause a malfunction.
• If you do not use the remote for an extended period of time,
remove the batteries to avoid possible damage from battery
leakage and corrosion.
4
Getting Started
When to use the COMMAND MODE selector
Hookups
The COMMAND MODE selector is set to CD1 at the
factory for normal use. You can control this player by
connecting to a Sony CD player with the player control
function, via the CONTROL A1 jacks. When making this
connection, set the COMMAND MODE selectors of each
player to the appropriate position according to the
connected line input jacks. For details, refer to the
instructions supplied with the connected player.
When connecting the audio cord, be sure to match the
color-coded cord to the appropriate jacks on the
components: Red (right) to Red and White (left) to
White. Be sure to make connections firmly to avoid
hum and noise.
CD player
Amplifier
LINE
OUT
INPUT
CD
L
COMMAND MODE
L
CD
R
R
1
2
3
• If you have a digital component such as a digital
amplifier, D/A converter, DAT or MD
Connect the component via the DIGITAL OUT (OPTICAL)
connector using an optical cable (not supplied). Take off the
cap and plug in the optical cable.
When using another Sony CD player together with
this player
You can make the supplied remote effective only for this
player.
• When using the player equipped with the
COMMAND MODE selector:
POC-15
Set the COMMAND MODE selector of this player to
CD1 and that of another player to CD2 or CD3. Then
set the CD1/2/3 switch on the remote supplied for
each player accordingly.
• When using the player not equipped with the
COMMAND MODE selector:
The command mode of the player without the
COMMAND MODE selector is set to CD1. Set the
COMMAND MODE selector of this player to CD2, and
set the CD1/2/3 switch on the remote to CD2.
Optical cable (not supplied)
CD player
Digital component
DIGITAL INPUT
DIGITAL
OUT
OPTICAL
OPTICAL
Note
When you connect via the DIGITAL OUT (OPTICAL)
connector, noise may occur when you play CD software
other than music, such as a CD-ROM.
Setting the voltage selector (voltage
selector equipped models only)
Check that the voltage selector on the rear panel of the
player is set to the local power line voltage. If not, set
the selector to the correct position using a screwdriver
before connecting the AC power cord to a wall outlet.
• If you have a Sony receiver (amplifier) equipped with
the CONTROL A1 jack
Be sure to connect the player to the CD IN jacks on the
receiver (amplifier). When making this connection, set the
COMMAND MODE of the player to CD1. If you further
connect the player and the receiver (amplifier) via the
CONTROL A1 jacks with the CONTROL A1 cord (supplied
for Canadian models only), you can use the Auto Function
feature between these components. For details, refer to the
supplementary “S-LinkTM/CONTROL-A1 Control System”
instructions and the instructions supplied with the receiver
(amplifier).
110 - 120 V
220 - 240 V
5
Getting Started
Connecting the AC power cord
Inserting CDs
Connect the AC power cord to a wall outlet.
You can insert up to 51 discs into this player.
Note on placement
I/u
PUSH OPEN
JOG
Be sure to place the player on a horizontal place.
If the player is slanted, it may cause a malfunction or
damage the player.
PUSH
OPEN
Playing position
Rotary table
Loading position
1
2
Press I/u to turn on the player.
Open the front cover by pushing PUSH OPEN of
the cover.
Front cover
3
Turn the JOG dial until you find the disc slot
where you want to insert a disc, while checking the
disc number (written beside every slot and also
indicated in the display).
Disc number
Disc slot at the loading position
6
Getting Started
The disc number at the loading position appears in
the display.* As you turn the JOG dial, the disc
number changes.
6
Close the front cover by pushing PUSH OPEN of
the cover until it clicks.
ALL DISCS
1
2
3
4
5
6
7
8
d1SC
2 0
CD 1
Disc number
You can play the disc you want independently by
using the Plus One function. When using this
function, insert the disc into the PLUS ONE slot.
For details, see “Playing Your Favorite Disc
Independently” on page 15.
You can arrange your discs into groups and play
them within a certain group using the Block Play
function. When using this function, you have to
insert discs into the slots assigned to one of the five
blocks. For details, see “Playing Discs in a Group”
on page 16.
The rotary table turns and the disc slot at the
loading position is set to the playing position.
Always close the front cover except when you
insert or remove discs.
The supplied CD booklet holder helps you locate a
disc
You can store up to 50 CD booklets.
Notes
• Do not insert an empty 8 cm (3-inch) CD adaptor (CSA-8). It
may damage the player.
* If you have already inserted discs, the disc number at
the playing position appears.
• Do not attach anything such as seals or sleeves to CDs. It may
damage the player or the disc.
• If you drop a disc into the player and the CD won’t go into
the slot correctly, consult your nearest Sony dealer.
• When transporting the player, remove all discs from the
player.
4
Insert a disc with the label side facing right.
Notes
• Make sure you have inserted the disc into each slot at
a right angle to the rotary table. If the disc is not put
in straight, it may damage the player or the disc.
• Make sure the rotary table comes to a complete stop
before inserting or removing discs.
Removing CDs
After following Steps 1 to 3 of “Inserting CDs” on
pages 6 – 7, remove the discs. Then close the front
cover.
Note
The disc being played does not come to the loading position if
you open the front cover. (The disc number flashes in the
display.)
With the label
side facing right
If you want to remove the disc being played, push the JOG
dial after opening the front cover. The disc comes to the
loading position. Remove the disc after the rotary table comes
to a complete stop.
5
Repeat Steps 3 and 4 to insert more discs.
7
Basic Operations
Playing a CD
2
3 5 4/5
STANDBY
PUSH
OPEN
DISC
I /
u
PUSH ENTER
BLOCK
PLAY MODE REPEAT
BLOCK FILE
1
2
3
4
5
CHECK
CLEAR
PLUS ONE
• See pages 4 – 5 for the hookup
Turn on the amplifier and select the CD player position.
information.
1
2
3
• Make sure you have inserted the
discs correctly as indicated on
page 6.
Press I/u to turn on the player.
• You can play all the tracks on a
disc in the original order
(Continuous Play). You can also
play up to 51 discs
Press PLAY MODE to select ALL DISCS or 1 DISC Continuous
Play mode.
consecutively.
When you select
The player plays
You can turn on the player
by pressing I/u on the
remote Z
ALL DISCS
All discs in the player consecutively in the order of
disc number. Empty disc slots are skipped.
1 DISC
Only the one disc you have selected
Turn the JOG dial until the disc number you want appears in
the display to select the first disc (ALL DISCS) or the disc you
want (1 DISC).
4
ALL DISCS
1
2
3
4
5
6
7
8
d1SC
2 0
CD 1
8
Basic Operations
Push the JOG dial or press · to start playing.
The selected disc is set to the playing position, and the player
plays all the discs from the selected one (ALL DISCS) or all the
tracks once (1 DISC).
5
Adjust the volume on the amplifier.
When you turn off the player
by pressing the I/u (standby
mode)
The player remembers the
last playing disc and the
play mode (Continuous,
Shuffle (see page 12) or
Program (see page 13)).
When you turn on the
player again, therefore, the
player plays the same disc in
the same play mode. Note
that the player does not
remember this information,
if you turn off the player by
pressing the power switch of
the amplifier or receiver
while the AC power cord is
connected to the switched
AC outlet of the amplifier or
receiver.
Display information while playing a disc
While playing a disc, the display shows the current disc number, track
number, playing time of the track and the next disc number.
Next disc number
Current disc number
ALL DISCS
1
2
3
4
5
6
7
8
DISC
TRACK
NEXTDISC
MIN
SEC
20 1
0 28 38
CD 1
Current track number
Playing time of the track
To stop playback
Press p.
Front cover
JOG
STANDBY
PUSH
OPN
DISC
I
/
u
PUSH ENTER
BLOCK
3
PLAY MODE REPEAT
BLOCK FILE
1
2
4
5
CHECK
CLEAR
PLUS ONE
P
p
·
≠/±
To
You need to
Press P
Pause
Resume playing after pause
Go to the next disc
Press P or ·
Press DISC SKIP + once.
Hold down the button to skip discs.
Go back to the preceding disc
Press DISC SKIP – once.
Hold down the button to skip discs.
Go to the next track
Press ±
Go back to the preceding track
Stop playing and remove the disc
Press ≠
Open the front cover, then push the JOG
dial. The disc comes to the loading
position.
9
Playing CDs
Locating a Specific Disc
Specifying the Next Disc to
Play
·
JOG
You can specify the next disc to play while playing a
disc in Continuous or 1 DISC Shuffle Play mode.
While playing a disc, turn the JOG dial until the disc
number you want appears in the display.
Next disc number
ALL DISCS
1
2
3
4
5
6
7
8
DISC
TRACK
NEXTDISC
MIN
SEC
20 1
0 28 38
CD 1
After the current disc is played, the next disc you have
specified starts playing.
If you want to skip to the next disc right away, push
the JOG dial while playing the current disc.
DISC
Number
buttons
To cancel the disc you have specified
Press CONTINUE twice.
ENTER
·
Locating a Specific Track or a
Point in a Track
You can quickly locate any track while playing a disc
using the ≠/± (AMS: Automatic Music Sensor)
buttons. You can also locate a specific point in a track
while playing a disc.
Selecting a disc on the player
Turn the JOG dial until the disc number you want
appears in the display. Push the JOG dial or press ·
to start play.
≠/±
Selecting a disc directly using the remote
1
Press DISC.
2
Press the number button of the disc.
Example: To enter number 35
Press 3, then 5.
3
Press ENTER or press · to start play.
To cancel the disc you have selected
Press CLEAR.
10
Playing CDs
Playing Repeatedly
You can play discs/tracks repeatedly in any play
mode.
REPEAT
Number
buttons
>10
=/+
0/)
Press REPEAT while playing a disc.
“REPEAT” appears in the display. The player repeats
the discs/tracks as follows:
When the disc is played in
The player repeats
ALL DISCS Continuous Play
(page 8)
All tracks on all discs
To locate
Press
1 DISC Continuous Play
(page 8)
All tracks on the current disc
the next or
± repeatedly until you find the
succeeding tracks
track
ALL DISCS Shuffle Play
(page 12)
The player does not repeat
discs/tracks but keeps
shuffling until you stop play
whether or not you press
REPEAT.
the current or
preceding tracks
≠ repeatedly until you find the
track
a specific track
directly Z
The number button of the track on the
remote. When you locate a track with
a number over 10, press >10 first, then
press the 10’s digit and 1’s digit.
1 DISC Shuffle Play
(page 12)
All tracks on the current disc
in random order
Program Play (page 13)
The same program
a point in a track
) (forward) or 0 (backward) and
while monitoring the hold down until you find the point
sound Z
a point in a track
quickly by observing hold down until you find the point
the display Z
) (forward) or 0 (backward) and
To cancel Repeat Play
Press REPEAT twice.
during pause. You will not hear the
sound during the operation.
Repeating the current track
Note
If “
” appears in the display, the disc has reached the end
You can repeat only the current track.
while you were pressing ) on the remote. Press ≠ or
0 on the remote to go back.
While the track you want is being played, press
REPEAT repeatedly until “REPEAT 1” appears in the
display.
To cancel Repeat 1
Press REPEAT.
11
Playing CDs
Playing all tracks on a specfied disc in
random order
Playing in Random Order
(Shuffle Play)
1
Press PLAY MODE repeatedly until “1 DISC” and
“SHUFFLE” appear in the display.
You can have the player “shuffle” the tracks and play
in random order. The player shuffles all the tracks on
all discs or on the disc you specified.
When using the remote, press SHUFFLE twice.
2
Turn the JOG dial until the disc number you want
appears in the display.
When using the remote, press DISC first and then
press the number button of the disc.
PLAY MODE
·
JOG
3
Push the JOG dial or press ·.
When using the remote, press ENTER.
1 DISC Shuffle Play starts.
“
” appears in the display while the player is
“shuffling” the tracks.
To cancel Shuffle Play
Press PLAY MODE repeatedly until “SHUFFLE” disappears
from the display. When using the remote, press CONTINUE.
SHUFFLE
DISC
You can start Shuffle Play while playing
Press PLAY MODE repeatedly until “SHUFFLE” appears
in the display. When using the remote, press SHUFFLE.
Shuffle Play starts from the current track.
Number
buttons
ENTER
You can specify the next disc to play during 1 DISC
Shuffle Play
Turn the JOG dial to specify the next disc. After all the
tracks on the current disc are played in random order,
the next disc starts playing. If you want to skip to the
next disc right away, push the JOG dial while playing the
current disc.
·
Note
You cannot specify the next disc to play during ALL DISCS
Shuffle Play.
Playing all tracks on all discs in random
order
1
Press PLAY MODE repeatedly until “ALL DISCS”
and “SHUFFLE” appear in the display.
When using the remote, press SHUFFLE.
2
Push the JOG dial or press ·.
ALL DISCS Shuffle Play starts.
“
” appears in the display while the player is
“shuffling” the discs or the tracks.
Note that ALL DISCS Shuffle Play continues until
you press p.
12
Playing CDs
4
Push the JOG dial.
Creating Your Own Program
(Program Play)
The track being programmed
1
2
3
4
5
6
7
8
DISC
TRACK
STEP
You can arrange the order of the tracks and/or discs to
create your own program and the program is stored
automatically. A program can contain up to 32 “steps”
— one “step” may contain a track or a whole disc.
You can make a program using the controls on the
remote as well as ones on the player. However, the
programming procedures are different.
20 1
1
PROGRAM
CD 1
Playing order
The disc being
programmed
5
6
To program other discs/tracks, do the following:
Repeat Steps
2 and 4
To program
Creating a program on the player
All tracks of another disc(s)
Other tracks on the same disc
Other tracks on other discs
3 and 4
PLAY MODE
CHECK
JOG
2 to 4
Push the JOG dial or press · to start Program
Play.
To cancel Program Play
Press PLAY MODE.
· ≠/± CLEAR
The program remains even after Program Play ends
When you push the JOG dial or press ·, you can play
the same program again.
1
2
Press PLAY MODE repeatedly until “PROGRAM”
appears in the display.
If a program is already stored, the last step of the
program appears in the display. When you want to
erase the whole program, hold down CLEAR until
“Clear” appears in the display (see page 14).
When you press PLAY MODE to select Program Play
during Continuous or Shuffle Play
The program will be played after the current track.
Turn the JOG dial until the disc number you want
appears in the display.
The program remains until you erase them
Even if you replace discs, the programmed disc and track
numbers remain. So, the player plays only the existing
disc and track numbers. However, the disc and track
numbers that are not found in the player or on the disc
are deleted from the program, and the rest of the
program is played in the programmed order.
1
2
3
4
5
6
7
8
DISC
TRACK
STEP
20 AL
1
PROGRAM
CD 1
Disc number
3
To program a whole disc, skip this step. Press
≠/± until the track number you want
appears in the display.
Note
If you press one of the BLOCK 1 – 5 buttons (see page 16) or
the PLUS ONE button (see page 15) during Program Play,
Program Play will be canceled.
1
2
3
4
5
6
7
8
DISC
TRACK
STEP
20 1
1
PROGRAM
CD 1
Track number
13
Playing CDs
Creating a program using the remote
Checking the programmed order
You can check your program before or after you start
playing.
Press CHECK.
PROGRAM
Each time you press this button, the display shows the
disc and track number of each step in the programmed
order. (When a whole disc is programmed as one step,
“AL” appears instead of the track number.) After the
last step in the program, the display shows “End” and
returns to the original display.
DISC
Number
buttons
ENTER
CLEAR
>10
CHECK
Changing the programmed order
·
You can change your program before you start playing.
To
You need to
Erase a track or disc
Press CHECK until the track or
disc you want to erase appears in
the display, then press CLEAR
Erase the last track or
disc in the program
Press CLEAR. Each time you
press the button, the last track or
disc will be cleared.
1
2
3
4
Press PROGRAM.
Add tracks or discs to the
end of the program
Follow the programming
procedure
Press DISC.
Change the whole
program completely
Hold down CLEAR until
“Clear” appears in the display to
erase the whole program, then
create a new program following
the programming procedure
Press the number button of the disc.
To program a whole disc, press ENTER and go to
Step 6.
5
6
Press the >10 button, then the number button of
the track.
Erasing the program stored in memory
1
Press PLAY MODE repeatedly until “PROGRAM”
appears in the stop mode. When using the remote,
press PROGRAM.
To program other discs/tracks, do the following:
To program
Repeat Steps
2 to 4
2
Hold down CLEAR until “Clear” appears in the
display.
All tracks of another disc(s)
Other tracks on the same disc
Other tracks on other discs
5
2, 3 and 5
7
Press · to start Program Play.
To cancel Program Play
Press CONTINUE.
14
Playing CDs
If you have already inserted a disc into the PLUS ONE
slot
Press PLUS ONE while the front cover is closed. Plus
Playing Your Favorite Disc
Independently (Plus One Play)
One Play starts immediately.
When you insert a disc into the PLUS ONE slot, you
can play the disc independently from other discs.
The play mode you have selected (except for Program
Play) remains active even if you use this function.
You can change the play mode by pressing the PLAY
MODE button before Step 4
Notes
• When you press the PLUS ONE button, ALL DISCS Play
mode is automatically set to 1 DISC Play mode.
• Plus One Play will be canceled if you turn the JOG dial or
press buttons to specify another disc or to select another
play mode.
Front cover
• The PLUS ONE slot comes to the loading position
automatically if you open the front cover during Plus One
Play. Do not put your hand inside the compartment nor
change the disc before the rotary table comes to a complete
stop. If you do, you may injure your hand or damage the
disc.
PLUS ONE
1
2
Open the front cover.
Press PLUS ONE.
The indicator on the PLUS ONE button lights up.
1DISC
1
2
3
4
5
6
7
8
d1SC PL US
1
CD 1
The PLUS ONE slot comes to the loading position.
PLUS ONE slot
3
4
Insert a disc into the PLUS ONE slot.
Close the front cover.
“P1” appears in the display instead of the disc
number, and the player starts playing the disc in
the PLUS ONE slot.
1DISC
1
2
3
4
5
6
7
8
DISC
TRACK
MIN
SEC
P1 1
0 35
CD 1
To cancel Plus One Play
Press PLUS ONE. The indicator on the PLUS ONE button
goes off. The disc number in the display changes to 51 and
you can play the disc as the 51st disc.
15
Playing CDs
1
2
Insert discs into the slot of the block you want,
referring to the table on page 16 (see also
“Inserting CDs” on page 6).
Playing Discs in a Group
(Block Play)
Press one of the BLOCK 1 – 5 buttons to select the
block.
When using the remote, press BLOCK, the number
button of the block you want, then ENTER.
The block number appears in the display.
You can classify discs in advance by artists, category,
etc. when inserting discs into the slots, and play them
only within the group (called “block”) you specified.
The player has five blocks, and each slot is assigned to
one of the blocks as shown below.
3
Push the JOG dial or press ·.
Block number
Disc slot
1–10
Block Play starts from the disc which is the most
upward number within a block and located closest
to the playing position.
1
2
3
4
5
11–20
21–30
31–40
41–51
You can start Block Play from the disc you want
When you want to start Block Play from the disc you
want, turn the JOG dial to select the disc after Step 2,
then push the JOG dial or press ·.
You can enjoy Continuous, Shuffle or Repeat Play
within a certain block.
To cancel Block Play
Press the corresponding BLOCK 1 – 5 button.
JOG
BLOCK 1 – 5
Notes
• The block number does not appear if no disc is put into the
block you specified.
• Block Play will be canceled if you press the PLAY MODE
button or the PROGRAM button on the remote to select
Program Play.
• Block Play will be canceled if you press the PLUS ONE
button.
·
BLOCK
Number
buttons
ENTER
·
16
Additional Information
On transportation
• When transporting the player, open the front cover then
remove all the discs from the player and turn the power off.
Precautions
On safety
If you have any questions or problems concerning your
player, please consult your nearest Sony dealer.
• Caution — The use of optical instruments with this product
will increase eye hazard.
• Should any solid object or liquid fall into the cabinet,
unplug the player and have it checked by qualified
personnel before operating it any further.
Notes on CDs
On power sources
On handling CDs
• To keep the disc clean, handle the disc carefully.
• Do not stick paper or tape on the disc.
• Before operating the player, check that the operating
voltage of the player is identical with your local power
supply. The operating voltage is indicated on the nameplate
at the rear of the player.
• The player is not disconnected from the AC power source
(mains) as long as it is connected to the wall outlet, even if
the player itself has been turned off.
• If you are not going to use the player for a long time, be
sure to disconnect the player from the wall outlet. To
disconnect the AC power cord (mains lead), grasp the plug
itself; never pull the cord.
• AC power cord must be changed only at the qualified
service shop.
Not this way
• Do not expose the disc to direct sunlight or heat sources
such as hot air ducts, nor leave it in a car parked in direct
sunlight as there can be considerable rise in temperature
inside the car.
On placement
• After removing a disc from the disc slot, store the disc in its
case.
• Place the player in a location with adequate ventilation to
prevent heat build-up in the player.
• Do not place the player on a soft surface such as a rug that
might block the ventilation holes on the bottom.
• Do not place the player in a location near heat sources, or in
a place subject to direct sunlight, excessive dust or
mechanical shock.
On cleaning
• Before playing, clean the disc with a cleaning cloth. Wipe
the disc from the center out.
On operation
• If the player is brought directly from a cold to a warm
location, or is placed in a very damp room, moisture may
condense on the lenses inside the player. Should this occur,
the player may not operate properly. In this case, leave the
player turned on for about an hour until the moisture
evaporates.
• Do not use solvents such as benzine, thinner, commercially
available cleaners or anti-static spray intended for vinyl
LPs.
On adjusting volume
• Do not turn up the volume while listening to a portion with
very low level inputs or no audio signals. If you do, the
speakers may be damaged when a peak level portion is
played.
On cleaning
• Clean the cabinet, panel and controls with a soft cloth
slightly moistened with a mild detergent solution. Do not
use any type of abrasive pad, scouring powder or solvent
such as alcohol or benzine.
17
Additional Information
Troubleshooting
Specifications
If you experience any of the following difficulties while
using the player, use this troubleshooting guide to help
you remedy the problem. Should any problem persist,
consult your nearest Sony dealer.
Compact disc player
Laser
Semiconductor laser (λ = 780 nm)
Emission duration: continuous
Laser output
Max 44.6 µW*
* This output is the value measured at
a distance of 200 mm from the
objective lens surface on the Optical
Pick-up block with 7 mm aperture.
There is no sound.
/Check that the player is connected securely.
/Make sure you operate the amplifier correctly.
Frequency response
Signal-to-noise ratio
Dynamic range
2 Hz to 20 kHz ± 1 dB
More than 100 dB
More than 88 dB
Less than 0.013 %
More than 95 dB
The CD does not play.
/There is no CD in a slot (“no dISC” appears).
Insert a CD.
/Insert the CD with the label side facing right.
/Clean the CD (see page 17).
/Moisture has condensed inside the player. Open
the front cover and leave the player turned on
for about an hour (see page 17).
Harmonic distortion
Channel separation
Output
Jack
type
Maximum
output
level
Load impedance
The remote does not function.
/Remove obstacles in the path of the remote and
the player.
/Point the remote at the remote sensor gon the
player.
/Replace all the batteries in the remote with new
ones if they are weak.
Phono
jacks
2 V
Over 10 kilohms
LINE OUT
(at 50 kilohms)
Optical
output
connector
– 18 dBm
Wave length: 660 nm
DIGITAL
OUT
(OPTICAL)
/Set the CD1/2/3 switch on the remote
according to the position of the COMMAND
MODE selector displayed in the front panel
display (see page 5).
General
Power requirements
Where purchased
USA/Canada
Australia
Power requirements
120 V AC, 60 Hz
The player functions incorrectly.
240 V AC, 50 Hz
/The microcomputer chips may be operating
incorrectly. Disconnect the AC power cord, then
connect it back to the wall outlet to reset the
player.
Europe
220 V – 230 V AC, 50/60 Hz
Other countries
110 V –120 V or 220 V – 240 V
AC, adjustable, 50/60 Hz
Power consumption
12 W
Dimensions (approx.)
(w/h/d)
When the front cover is closed
430 × 182.5 × 295 mm (17 × 7 1/4
× 11 5/8 in.) incl. projecting parts
When the front cover is open
430 × 182.5 × 414 mm (17 × 7 1/4
× 16 3/8 in.) incl. projecting parts
Mass (approx.)
5.2 kg (11 lbs 8 oz)
Supplied accessories
Audio cord (2 phono plugs – 2 phono plugs) (1)
CONTROL A1 cord (supplied for Canadian models only) (1)
Remote commander (remote) (1)
Sony SUM-3 (NS) batteries (2)
CD booklet holder (1)
Label (1)
Design and specifications are subject to change without notice.
18
Index
Names of controls
S
T
Index
Searching. See Locating
Selecting a disc 10
Shuffle Play
Buttons
BLOCK 16
on all discs 12
A
BLOCK 1 – 5 16
CHECK 14
on one disc 12
Specifying the next disc 10
AMS 10
Automatic Music Sensor 10
CLEAR 14
CONTINUE 10
DISC 10
B
Troubleshooting 18
DISC SKIP
9
Block Play 16
ENTER 10
Number 10
U, V, W, X, Y, Z
C, D
PLAY MODE
8
Unpacking
4
Connecting
Continuous Play
4
PLUS ONE 15
8
PROGRAM 14
REPEAT 11
SHUFFLE 12
E, F, G
Erasing
programs 14
≠/±
9
0/) 11
·
P
9
9
9
H
I
p
Handling CDs 17
Hookups
>10 11
overview
4
Switches
CD1/2/3
5
I/u
6
Inserting CDs
6
Jacks
J, K
LINE OUT
5
JOG dial 6, 8
S-LINK/CONTORL A1
5
L, M, N, O
Connectors
Locating
DIGITAL OUT (OPTICAL)
5
a specific track 11
a specific point 11
by monitoring 11
by observing the display 11
discs 10
Others
Disc slots
Display
Front cover
6
9
using AMS 11
6
JOG dial 6, 8
PUSH OPEN
Rotary table
6
6
P, Q
Playback
g
4
Block Play 16
Continuous Play
Program Play 13
Repeat Play 11
Shuffle Play 12
Plus One Play 15
Program
8
changing 14
checking 14
erasing 14
R
Remote control
Repeating 11
4
Rotary table
6
19
Sony Corporation Printed in China
|