Related Documents
To install the AT-WDRPS-10, perform the following procedure:
way to access the most recent documentation, software, and technical information
for all of our products. For details on the features and functions of your Allied
Telesyn AT-WD1008 chassis and modules, refer to the following manuals from our
web site:
Note
The AT-WDRPS-10 unit can be installed while the multiplexer is powered ON.
You do not need to power OFF the multiplexer to install the RPS.
❑ AT-WD1008 Gigabit Ethernet Wavelength Division Multiplexer
1. Loosen the two thumbscrews that secure the blank faceplate over the right-
hand redundant power supply expansion slot located on the front panel of the
AT-WD1008 Multiplexer and remove the cover.
Installation Guide
PN 613-50367-00
❑ AT-S47 Management Software User’s Guide
S
T
TX
PN 613-50371-00
TX
L
N
K
T
S
T
X
X
RX
AT-WDRPS-10
Redundant Power Supply (AC)
L
N
K
T
S
T
T
TX
WEST
RX
T
R
X
X
EAST
R
RX
TX
RX
L
N
K
T
S
T
TX
E
A
N
S
T
O
R
M
A
L
C
H
5
RX
TX
TX
Package Contents
C
H
6
RX
TX
RX
RX
TX
Installation Guide
C
H
7
TX
RX
Make sure the following items are included in the shipping package. If any item is
missing or damaged, contact your Allied Telesyn sales representative for
assistance.
F
AN
A
B
P
O
S
W
E
N
M
R
B
S
P
U
M
P
O
P
D
U
L
Y
L
E
C
H
8
F
AN
❑ One AT-WDRPS-10 Redundant Power Supply (AC) Module
❑ One AC Power Cord
Allied Telesyn, Inc.
960 Stewart Drive, Suite B
Sunnyvale, CA 94085 USA
❑ This installation guide
Tel 1 (408) 730-0950 • Fax 1 (408) 736-0100
❑ Warranty card
2. Remove the AT-WDRPS-10 unit from its shipping package.
3. Slide the AT-WDRPS-10 unit into the RPS expansion slot.
Installing the AT-WDRPS-10 Power Supply
T
X
TX
RX
L
N
K
T
S
T
X
X
R
X
T
L
N
Caution
K
T
S
T
T
X
X
X
W
E
T
S
R
T
E
A
S
R
T
R
X
TX
RX
L
N
K
T
S
T
T
X
EAST
TX
N
O
R
M
A
L
Before installing the module, refer to the AT-WD1008 Installation Guide for
electrical safety and emission information.
CH
5
R
X
T
X
CH
6
R
X
TX
RX
RX
T
X
Overview
CH
7
TX
RX
F
AN
A
B
POWER
SNMP
SUPPL
MODULE
Y
B
CH
8
The AT-WDRPS-10 is an AC Redundant Power Supply (RPS) for the AT-WD1008
Multiplexer chassis. When installed, the unit shares the load of powering the
chassis with the standard power supply that comes pre-installed in the chassis. If a
power supply fails, the remaining unit provides all power to the system, thereby
preventing a network failure. The power supply is hot-swappable, meaning that
you can install it while the chassis is powered ON.
F
AN
Caution
Do not install the AT-WDRPS-10 module in an AT-WD1008 chassis designed
for DC power. An AC powered chassis has two AC power sockets on the back
panel.
P
O
W
E
R
F
A
U
L
T
P
O
W
E
R
F
A
U
L
T
PN 613-50369-00 Rev A
1
2
3
|
Acer Computer Monitor AL2216W User Manual
Adder Technology Computer Accessories CATX USBA DA User Manual
AEG Cooktop FM 6300G AN User Manual
AGFA Digital Camera DC 1338i User Manual
Aiphone Intercom System GH 1AD User Manual
Alpine Home Theater Server PXI H990 User Manual
American Standard Bathroom Aids 10 GPF User Manual
Asus Car Video System VH222 User Manual
Axis Communications Security Camera P5532 User Manual
Banner Stud Sensor P4 GEO 13 User Manual