GE Ventilation Hood JVB34 User Manual

SERVICING  
NOTE: BE SURE ELECTRICAL POWER IS  
Disconnect power to the cooktop and remove it first.  
Reverse the steps in the Install the Downdraft section  
to remove the downdraft from the cabinet.  
OFF BEFORE SERVICING THE UNIT.  
It may be necessary to remove the downdraft blower  
system from the cabinet in order to service components  
such as the blower motor or air vent mechanism.  
Service parts are available from your local GE  
distributor or from a GE Service and Parts Center.  
USING YOUR DOWNDRAFT VENT SYSTEM  
Controls  
Turn the downdraft blower  
ON by pressing down on  
the activating switch. The  
air vent will rise.  
Turn the downdraft  
blower OFF by pressing  
the activating switch  
again. The air vent will  
go down and the blower  
will shut off.  
The blower can be ON or  
OFF and its speed can be  
adjusted with the recessed  
knob on the right side of  
the air vent.  
NOTE: For most convenient operation, set the blower  
to your favorite speed. The blower will come on to  
this speed whenever the activating switch is pressed  
and the air vent rises.  
Knob  
CAUTION: Be careful when raising or lowering  
the downdraft. Be sure pots, pot handles and other  
objects are clear of the downdraft cover and cannot  
be struck or tipped by the downdraft being raised.  
• To avoid injury, make sure there are no fingers  
around the downdraft cover when it is lowered.  
• Keep hands and fingers away from all  
downdraft parts.  
COOKING TIPS  
• The high capacity performance of this downdraft  
system can increase the cooking times for some foods.  
It may take longer to reach high cooking temperatures  
if the downdraft is turned on to high right away.  
Adjust the fan speed for best cooking results.  
Canning  
When canning foods in a water-bath canner, a gentle  
but steady boil must be maintained continuously for  
the required time. When canning foods in a pressure  
canner, the pressure must be maintained continuously  
for the required time.  
For best results when heating oil for deep frying or  
when boiling water, use the front surface units or wait  
until the water is boiling or the oil is at frying  
temperatures before turning on the downdraft.  
Use of the blower at a high speed when canning may  
reduce the temperature enough to stop boiling. While  
canning, we recommend using the downdraft at LOW  
speed and using the front surface unit.  
• The downdraft may not completely capture all the  
steam from pans on the front burners.  
3
 
     
CARE AND CLEANING  
Grease Filter  
The efficiency of your downdraft depends on a clean  
filter. Frequency of cleaning depends on the type of  
cooking you do. Grease filters should be cleaned at  
least once a month. Never operate the downdraft  
without the filters in place.  
To remove: Pull the filters out by grasping them and  
pulling straight up.  
To clean: Soak and then agitate in a hot detergent  
solution. Light brushing may be used to remove  
imbedded soil. Rinse, shake and remove moisture  
before replacing.  
NOTE: The filters are different sizes. Be sure to  
With careful handling, the filter will last for years.  
If replacement becomes necessary, order the part from  
your dealer.  
replace them with the longer filter on the left.  
When replacing the filters, the long one goes in the  
left side.  
Blower  
Painted or Metal Surfaces  
1. DISCONNECT THE DOWNDRAFT  
POWER SUPPLY BY REMOVING THE  
POWER CORD FROM THE RECEPTACLE.  
Clean greasy surfaces frequently, using a mild  
detergent. Do not use abrasive cloth, steel wool  
pads or scouring powder because they will mar  
the surface.  
2. Remove the blower cover.  
3. Use a vacuum hose to clean the blower.  
Do not immerse the blower in water.  
Stainless Steel (on some models)  
4. Replace the blower cover.  
Clean with warm sudsy water, a stainless steel cleaner  
such as Kleen King®, or an all-purpose liquid or spray  
cleaner. Always scrub in the direction of the grain.  
Rinse thoroughly with a sponge or cloth and clean  
water. Dry with a soft, clean cloth.  
5. Reconnect the power supply.  
Do not use a soap-filled steel wool pad; it will scratch  
the surface.  
QUESTIONS?  
USE THIS PROBLEM SOLVER  
PROBLEM  
POSSIBLE CAUSE  
FAN DOES NOT WORK  
• The vent must be fully extended before the downdraft will work.  
• The blower control knob must be turned in a clockwise direction to turn  
the blower on.  
If you need more help…call toll free:  
GE Answer Center®  
800.626.2000  
consumer information service  
4